Home - Products - Auto Dialers & Data Loggers - Sensaphone Accessories
 |
Contact Type Magnetic Reed Door and Window Switch FGD-0006 Detect Unauthorized Entry or Intrusion. The magnetic reed switch may be used with all Sensaphone Models to detect any unauthorized entry or intrusion. They are usually installed on doors or windows to detect their opening and closing. Several magnetic reed switches may be wired in series to one Sensaphone input. The switch is usually installed to function in a normally closed position when the door or window is closed. The complete Magnetic Reed Switch assembly comes in two main parts: a magnet in a plastic housing, and a switch with screw terminals in another, separate plastic housing. |
 |
Contact Type Infrared Motion Detection Sensor FGD-0007 Monitor for the movement of warm bodies. The Infrared Motion Detection sensor can be used with all Sensaphone models to monitor the movement of warm bodies in a specific area. It will cause an alarm if motion is detected. Its range of detection covers approximately forty feet of area. Multiple sensors can be wired in series to a single output. |
 |
Contact Type Spot Water Detection Sensor FGD-0013 Detect water in small areas. The water detection sensor detects the presence of water on a horizontal surface. The device is compatible with any Sensaphone monitoring system. It can be used to detect leaks in homes or facilities. The sensor is independently powered by internal lithium batteries. The batteries should last for approximately 3-5 years. When the batteries start to run down, the sensor will automatically dial out an alarm when no water is present. Multiple sensors can be wired in series to a single input. The sensor is set as a normally open contact. |
 |
Contact Type Temp Alert Temperature Switch |
 |
Contact Type Humidistat Humidity Switch FGD-0027 Detect high or low humidity. The Humidistat Humidity Switch is a hard-wired humidity sensor that can be used with all Sensaphone models to detect high or low humidity levels. Users set a high or low alarm limit by adjusting the dial on the front of the sensor. When that limit is exceeded, the device will trip an alarm to the Sensaphone. Made from high impact white plastic, a nylon sensing element provides long life and accurate humidity control. The sensor has a range of 10% to 80% relative humidity. Multiple sensors may be wired to a single input. The humidistat switch can be installed in any location, home or office, and will work accurately for many years. |
 |
Contact Type Smoke Detector Sensor FGD-0049-B Smoke Detection. The Smoke Detector with battery backup and built-in relay utilizes a photoelectric sensing method and is designed for use in commercial and residential applications. The device requires hard-wired 120VAC 60Hz power. The detector features two sets of dry alarm contacts: one form-A SPST and one form-C SPDT. The detector has tandem interconnect capability allowing up to 6 devices to be connected together. A 90dBA audible horn is included. The smoke detector can be used with all Sensaphone models. A smoke detector with 220V power is also available, but does not inlcude battery backup. |
 |
Humidity Transmitter (4-20mA) FGD-0052 Monitor Humidity Levels. This sensor is a space mount, low profile humidity transducer that transmits actual humidity levels to a Sensaphone for programmable high and low alarm limits. The device can be used with any Sensaphone that supports 4-20mA inputs. The 24V DC power supply is required unless used with the SCADA 3000. |
 |
4-20mA Type Outdoor Humidity Transmitter FGD-0052-OD Monitor humidity in harsh locations. This humidity transmitter can be used with Sensaphone models that accept a 4-20mA signal to detect humidity levels. The device will cause your Sensaphone to activate an alarm when the humidity level reaches a set threshold. With a range of 0% to 100% RH level, the sensor causes an alarm when the humidity exceeds or falls below the set limit. The sensor is mounted in a weatherproof enclosure to allow for mounting in harsh locations. The sensor will need a 24VDC power supply to operate |
 |
24V Power Supply for 4-20mA Sensors FGD-0053 A 24V power supply for use with most 4-20mA sensors. This device provides two parallel 24V outputs that can be used to power up to two 4-20mA transducers or any 24VDC device that requires battery backup. The unit includes (4) AA NiMh rechargeable batteries that will keep the power supply running for several hours in the event of a power failure. Typical backup times are dependent on total current required by sensors. |
 |
Contact Type PowerOut Alert Power Failure Switch |
 |
Contact Type Zone Water Detection Sensor
|
 |
4-20mA Type Dew Point Sensor |
|
Contact Type Zone Water Detection Sensor
|
 |
Dual Setback Thermostat for 400/800 FGD-0064 Control the temperature between two set points. For use exclusively with the Sensaphone 400 and 800, this is a "setback" thermostat with an LCD readout. It lets you enter the desired setpoint for both your "away" and "home" temperatures. A control signal, sent from your Sensaphone, switches between these two settings. |
 |
4-20mA Type Carbon Monoxide Sensor FGD-0065 Monitor CO levels from 0-300 ppm. Carbon Monoxide is a highly toxic gas that has no color or odor. The Sensaphone Carbon Monoxide sensor will allow you to monitor CO levels from 0-300 ppm with any Sensaphone that will accept a 4-20mA input signal. The sensor is easy to install and provides reliable protection against the dangers of carbon monoxide. The 1” x .5” LCD displays the PPM and menu parameters. The sensor will require a 24VDC power supply to operate (Part # FGD-0070). |
 |
4-20mA Type Air Quality Sensor |
 |
Surge Suppressor for Power & Phone FGD-0067 Power surge protection. This surge suppressor offers complete AC and phone line surge suppression. The retractable plug prevents scratching of expensive portable electronics. A set of two RJ11 telephone line suppression jacks protect dialup and voice/modem lines. The suppressor offers two total outlets in a space saving direct plug-in format and diagnostic LEDs to warn of problems. |
 |
4-20mA Type Carbon Dioxide (CO2) Sensor FGD-0068 Carbon Dioxide monitoring. The Sensaphone Carbon Dioxide sensor will monitor levels of Carbon Dioxide from 0-2,000ppm with any Sensaphone that will accept a 4-20mA input signal. The sensor will need a 24VDC power supply to operate (Part # FGD-0070) |
 |
4-20mA Type Outdoor CO2 Transmitter FGD-0068-OD Monitor CO2 in harsh locations. The Sensaphone Carbon Dioxide sensor will detect levels of carbon dioxide from 0-20,000ppm. It is ideal for applications where higher levels of CO2 would be expected (>2,000 ppm), including breweries, wineries, plant greenhouses or where the building will generally be constantly occupied such as a hospital. The transmitter can be programmed to detect levels from 2,000 to 20,000ppm. Used with any Sensaphone that will accept a 4-20mA input signal, the device will provide real-time carbon dioxide data and will cause your Sensaphone to activate an alarm when the CO2 level reaches a set threshold. The weatherproof enclosure allows the sensor to be placed in areas that would typically shorten the life of other sensors. The sensor will need a 24VDC power supply to operate (Part # FGD-0053). |
 |
4-20mA Type Duct Mount Air Flow Transmitter FGD-0069 Monitor air flow in duct work. This air flow transmitter registers the airflow speed according to a thermal principal based on the fact that the cooling action of air increases with airspeed. Used with any Sensaphone that will accept a 4-20mA input signal, the device will provide real time data and will cause your Sensaphone to activate an alarm when the airflow reaches a set threshold. This is especially useful for monitoring air conditioning in ducts. The sensor can provide relative air flow from 0-16m/s. The sensor will need a 24VDC power supply to operate (Part # FGD-0070). |
 |
24VDC Power Supply Accessory for 4-20mA Sensors w/ Battery Backup FGD-0070 Power supply with battery backup. 4-20mA type transducers require an external power supply to operate when used with most Sensaphone devices. The 24VDC Power Supply with Battery Backup provides two parallel 24V outputs that can be used to power up to two 4-20mA transducers or any 24VDC device that requires battery backup. The unit includes (4) AA NiMh rechargeable batteries that will keep the transducers running for up to 24 hours in the event of a power failure. These devices are available with a domestic or international power supply. |
 |
Din Rail Mount 24V Power Supply Accessory FGD-0071 Modbus Sensor Power Supply. This 24V power supply is capable of providing up to 2.5 Amps of output current which can be used to power sensors, 4-20mA current loops, or other controls. The DIN rail mounting saves space in tight enclosures. It also features high efficiency, a wide input voltage range 88-264VAC, and UL approvals. The power supply is protected against overvoltage, overload and short-circuit conditions. |
 |
4-20mA Type Soil Moisture Sensor FGD-0090 Research grade accuracy. The soil moisture sensor determines volumetric water content (VWC) by measuring the dielectric constant of the media using capacitance/frequency domain technology. It minimizes salinity and textural effects, making it accurate in almost any soil or soil-less media. Factory calibrations are included for mineral soils, potting soils, and rockwool. The sensor will need a 24VDC power supply to operate (Part # FGD-0070) |
 |
Remote Temperature Sensor 2.8K FGD-0100 The 2.8K Remote Temperature sensor enables monitoring temperatures at a location away from a Sensaphone unit. It will measure and report the exact temperature back to the Sensaphone unit to which it is attached. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low temperature limits. It may be mounted anywhere air temperatures need to be measured, however this model is recommended to be located in clean, dry environment. For outdoor use model FGD-0101 is recommended. |
 |
2.8K Weatherproof Temperature Sensor FGD-0101 The 2.8K Weatherproof Remote Temperature sensor enables monitoring temperatures at a location away from a Sensaphone unit. It will measure and report the exact temperature back to the Sensaphone unit to which it is attached. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low temperature limits. It may be mounted anywhere air temperatures need to be measured and is suitable for use in wet, dirty environments. This is a highly recommended sensor for every cold storage application above -20°F. For colder temperatures we recommend using sensor part number FGD-0101-TEF. |
|
2.8K Weatherproof Temperature Sensor FGD-0101-NIST The 2.8K Weatherproof Remote Temperature sensor enables monitoring temperatures at a location away from a Sensaphone unit. It will measure and report the exact temperature back to the Sensaphone unit to which it is attached. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low temperature limits. It may be mounted anywhere air temperatures need to be measured and is suitable for use in wet, dirty environments. This is a highly recommended sensor for every cold storage application above -20°F. For colder temperatures we recommend using sensor part number FGD-0101-TEF. NIST temperature certification is available. |
 |
2.8K Ultra Low -85°C Temperature Sensor with Teflon |
 |
10K Remote Weatherproof Temperature Sensor FGD-0102 Weatherproof temperature monitoring. This sensor enables monitoring temperatures at a location away from a Sensaphone unit. It will measure and report the exact temperature back to the Sensaphone. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low temperature limits. It may be mounted anywhere air temperatures need to be measured and is suitable for use in wet, dirty environments. Available with NIST Certification. |
 |
10K Indoor Decorator Zone Temperature Sensor FGD-0103 Where appearance is important. The 10K indoor decorator zone temperature sensor offers precision room temperature sensing in an attractive wall–mounted enclosure. Accurate to 0.36°F (0.2°C) with a sensing range of 35° to 140°F. The indoor decorator comes in a beige plastic enclosure, with a tan metal face plate. The sensor is designed to be wall–mounted indoors where appearance is important. |
 |
10K Outdoor Air Weatherproof Temperature Sensor FGD-0104 The 10K Outdoor Air Weatherproof Temperature sensor is a sensitive temperature element with a stainless steel tube sheathe. It is mounted inside a ventilated, treated weather-resistant PVC shield to minimize radiant energy effects and mounted on a weatherproof outlet box for easy outdoor installation. Accurate to ±0.36°F (0.2°C) with a sensing range of -30° to 140°F. Eight feet of 24AWG wire is included. |
 |
10K Immersion Temperature Sensor FGD-0105 Fluid temperature monitoring. The 10K Immersion temperature sensor measures the temperature of fluids inside a pipe. It’s constructed of brass WEL-B thermowell (which screws into a customer-supplied 0.5” NPT saddle or Thredolet® fitting in a pipe). It fits into a thermowell via a brass 0.125” NPT fitting. |
 |
2.8K Temperature Sensor with Glass Bead Vial FGD-0107 Buffer momentary temperature fluctuations. This glass bead filled vial will buffer any momentary fluctuations that may cause a preliminary alarm dial out, such as defrost cycles, opening of doors, and fans circulating air. The glass beads will slow the response time of the sensor allowing normal daily operations to occur without having an alarm. |
|
2.8K Temperature Sensor with Glass Bead Vial FGD-0107-GBV Buffer momentary temperature fluctuations. This glass bead filled vial will buffer any momentary fluctuations that may cause a preliminary alarm dial out, such as defrost cycles, opening of doors, and fans circulating air. The glass beads will slow the response time of the sensor allowing normal daily operations to occur without having an alarm. |
 |
2.8K Ultra Low -85°C Temperature Sensor with Glass Bead Vial and Teflon Cable |
 |
Modbus Type Temperature and Humidity Combination Sensor |
 |
2.8K Type Temperature Sensor Display The Local Temperature Display also:
|
 |
2.8K Type Temperature Sensor Display FGD-0127 Buffer momentary temperature fluctuations. The Temperature Sensor in Glycol Vial can be used with most Sensaphone models to measure the temperature of objects in a refrigerator or freezer. By placing the sensor in a bottle filled with glycol users will receive a reading that represents the temperature of the refrigerator’s contents rather than the ambient air temperature. The Sensaphone will trigger an alarm when the temperature falls outside of the programmed high or low temperature limit. The glycol filled vial will also buffer any momentary fluctuations that may cause a preliminary alarm dial out, such as defrost cycles, opening of doors, and fans circulating air. The glycol will slow the response time of the sensor allowing normal daily operations to occur without having an alarm. The included 12 feet of wire can be extended with optional accessory wire. |
|
2.8K Type Temperature Sensor Display FGD-0127-NIST Buffer momentary temperature fluctuations. The Temperature Sensor in Glycol Vial can be used with most Sensaphone models to measure the temperature of objects in a refrigerator or freezer. By placing the sensor in a bottle filled with glycol users will receive a reading that represents the temperature of the refrigerator’s contents rather than the ambient air temperature. The Sensaphone will trigger an alarm when the temperature falls outside of the programmed high or low temperature limit. The glycol filled vial will also buffer any momentary fluctuations that may cause a preliminary alarm dial out, such as defrost cycles, opening of doors, and fans circulating air. The glycol will slow the response time of the sensor allowing normal daily operations to occur without having an alarm. The included 12 feet of wire can be extended with optional accessory wire. |
 |
2.8K Type Ultra Low Temperature Sensor in Glycol Bottle FGD-0127-TEF Buffer momentary temperature fluctuations. The FGD-0127-TEF is ideal for cold storage temperature monitoring where temperatures are consistently under -20°C. The glycol filled bottle will buffer any momentary fluctuations that may cause a preliminary alarm dial out, such as defrost cycles, opening of doors, and fans circulating air. The glycol will slow the response time of the sensor allowing normal daily operations to occur without having an alarm initiated. |
|
2.8K Type Ultra Low Temperature Sensor in Glycol Bottle FGD-0127-TEFNIST Buffer momentary temperature fluctuations. The FGD-0127-TEFNIST is ideal for cold storage temperature monitoring where temperatures are consistently under -20°C. The glycol filled bottle will buffer any momentary fluctuations that may cause a preliminary alarm dial out, such as defrost cycles, opening of doors, and fans circulating air. The glycol will slow the response time of the sensor allowing normal daily operations to occur without having an alarm initiated. |
 |
J Type Thermocouple / 4-20mA Converter FGD-0220 Out of range temperature monitoring. The thermocouple to 4-20mA converter is useful when you need to monitor very high or very low temperatures that can not be monitored with a standard Sensaphone temperature sensor. Thermocouples are available in a variety of packages that may be perfectly suited to your measuring application. The device can be used with any Sensaphone that supports 4-20mA inputs. |
 |
Contact Type Float Level Switch FGD-0222 Monitor fluid levels. The FGD-0222 float switch is a plastic side mounted float switch. It is cost effective for level control applications in small tanks where it is more convenient to install a level switch through the sidewall of the tank. This style float switch can be rotated for Normally Open or Normally Closed operation. Combine two switches at different levels for high and low level or pump control or alarming. |
 |
4-20mA Type Dual Flow & Temperature Sensor FGD-0223-1 Thermal Flow Meter with Digital Display The Sensaphone Dual Flow and Temperature Sensor will measure and provide real time flow rates to any Sensaphone that accepts a 4-20mA signal. When the flow rate falls outside of the Sensaphone’s programmed high or low limit, the user will receive an alarm which displays or reads the current flow rate. The sensor can be used to detect and measure the flow of oil, water, glycol and air in internal pipe diameters up to 10”. A simple pushbutton menu allows the sensor to be programmed to fit your application setpoints. Switching, frequency or analog outputs are also selectable. Designed with an integrated digital display, values may be set in green or red for indicating if process values are within range or if limits have been exceeded. Two sensors are available to fit pipes from .5” to 10”. A 24V DC power supply is required to power the sensor. |
 |
4-20mA Type Dual Flow & Temperature Sensor FGD-0223-4 Thermal Flow Meter with Digital Display The Sensaphone Dual Flow and Temperature Sensor will measure and provide real time flow rates to any Sensaphone that accepts a 4-20mA signal. When the flow rate falls outside of the Sensaphone’s programmed high or low limit, the user will receive an alarm which displays or reads the current flow rate. The sensor can be used to detect and measure the flow of oil, water, glycol and air in internal pipe diameters up to 10”. A simple pushbutton menu allows the sensor to be programmed to fit your application setpoints. Switching, frequency or analog outputs are also selectable. Designed with an integrated digital display, values may be set in green or red for indicating if process values are within range or if limits have been exceeded. Two sensors are available to fit pipes from .5” to 10”. A 24V DC power supply is required to power the sensor. |
 |
RTD Probe with 4-20mA Transmitter FGD-0240 Measure extreme temperatures. The RTD probe with 4-20mA transmitter can be used to measure the temperature in extreme environments. The standard transmitter is calibrated to operate over the range -200° to 35°C, but can be customized at time of order to operate over any range between -200° and 204°C. Two temperature sensing probes are available. The 14" probe is useful for applications such as monitoring liquid nitrogen, where the sensor cabling cannot be exposed to the cold atmosphere. The sensor will need a 24VDC power supply to operate (Part # FGD-0070) |
|
RTD Probe with 4-20mA Transmitter FGD-0240-SPEC Measure extreme temperatures. The RTD probe with 4-20mA transmitter can be used to measure the temperature in extreme environments. The standard transmitter is calibrated to operate over the range -200° to 35°C, but can be customized at time of order to operate over any range between -200° and 204°C. Two temperature sensing probes are available. The 14" probe is useful for applications such as monitoring liquid nitrogen, where the sensor cabling cannot be exposed to the cold atmosphere. The sensor will need a 24VDC power supply to operate (Part # FGD-0070) |
|
RTD Probe with 4-20mA Transmitter FGD-0240-14-SPEC Measure extreme temperatures. The RTD probe with 4-20mA transmitter can be used to measure the temperature in extreme environments. The standard transmitter is calibrated to operate over the range -200° to 35°C, but can be customized at time of order to operate over any range between -200° and 204°C. Two temperature sensing probes are available. The 14" probe is useful for applications such as monitoring liquid nitrogen, where the sensor cabling cannot be exposed to the cold atmosphere. The sensor will need a 24VDC power supply to operate (Part # FGD-0070) |
 |
Ethernet-to-WiFi Adapter Accessory FGD-0250 Add connectivity to any network based Sensaphone. The Ethernet-to-WiFi Adapter (FGD-0250) is a high-speed, long-range outdoor 802.11n Wireless Bridge/Access Point that operates on the 2.4 GHz band and is an ideal solution for adding wireless connectivity to any wired network device. The unit features an IP65-Rated weatherproof housing that ensures continued operation in harsh outdoor environments or in climates of extreme cold, heat, or continuous moisture. Also included is a proprietary PoE (Power-over-Ethernet) kit comprised of a PoE injector and Power Adapter as well as a mast mount kit with binding strap. |
 |
4G/LTE High Gain Omni Directional Antenna FGD-0260 Increase cell signal strength. This antenna can help to extend the range of the Sentinel with a 4G Cellular Modem’s cellular service. Versatile and easy to install, the antenna can be easily mounted on a wall or pole. It is ideal use when your Sentinel is mounted in locations that may interfere with the cellular coverage. The included 20’ LMR240 cable allows the antenna to be placed in a location that may receive better reception. |
 |
3G/4G/LTE External Antenna FGD-0261 Increase cellular signal strength. This external antenna provides improved wireless performance for Sensaphone cellular devices. The included 5m cable allows the antenna to be mounted away from the Sensaphone. A wall/mast mount bracket is standard but it can also be mounted on metal panels or enclosures of suffi cient size. Mount the antenna 6’ or more from the Sensaphone enclosure for best performance. The antenna is supplied with a convenient adhesive pad and an integrated 5m low loss cable run, the antenna is cost effective to install and adaptable to any install environment. |
 |
Serial-to-Ethernet Device Server FGD-0300 Access your Sensaphone SCADA 3000 anywhere on a local LAN or the Internet. The Serial-to-Ethernet Device Server allows you to access your Sensaphone SCADA 3000 anywhere on a local LAN or the Internet. Simply connect the device to the serial port on your Sensaphone and connect the Ethernet jack to your network. The software included with the device server will route your computer's serial port to the network-connected device server, thus establishing a fast, direct connection to your Sensaphone. |
 |
4-20mA Type Pressure Sensor FGD-0301 Receive alarms and datalog pressure values. The Sensaphone Pressure Sensor can be used to measure and detect loss of pressure in many applications. An alarm from the pressure sensor can indicate a problem with a pump, a possible clogged influent line, loss of suction, a downstream clog or perhaps a burst pipe. Any of those failures can cause a pump motor to overheat and warp. |
 |
4-20mA Type Differential Pressure Sensor FGD-0302 Measure static or differential pressure. A universal design monitors differential or static pressures in commercial buildings, these sensors offer exceptional job-site flexibility. Excellent tolerance to overpressure and vibration reduces field failures. High accuracy digital sensor maintains calibration and reduces callbacks. The sensors monitor positive and negative pressure for application versatility and the LCD is ideal for set-up, troubleshooting, and measuring. |
|
4-20mA Type Differential Pressure Sensor with Duct Mount Kit FGD-0302-DUCT Measure differential pressure in ducts |
|
4-20mA Type Differential Pressure Sensor with Wall Mount Kit FGD-0302-ROOM Measure differential pressure |
 |
4-20mA Type Vibration Sensor FGD-0303 Monitor the overall vibration of equipment. Implementation of continuous vibration monitoring has never been easier. Vibration on industrial equipment can be continuously monitored for unusual operating conditions and potential failure. The Sensaphone Vibration Monitor is designed to be permanently mounted on industrial equipment and continuously monitor the changes in a machine's vibration level. Detecting these changes early on prevents machinery from catastrophic failure, secondary damage, and expensive down time. The sensor continuously monitors real-time RMS vibration velocity and provides an analog output of the velocity to the Sensaphone. The sensor comes with a 5m cable and is available with an optional magnetic mounting base. |
|
4-20mA Type Vibration Sensor FGD-0303-MOUNT Monitor the overall vibration of equipment. Implementation of continuous vibration monitoring has never been easier. Vibration on industrial equipment can be continuously monitored for unusual operating conditions and potential failure. The Sensaphone Vibration Monitor is designed to be permanently mounted on industrial equipment and continuously monitor the changes in a machine's vibration level. Detecting these changes early on prevents machinery from catastrophic failure, secondary damage, and expensive down time. The sensor continuously monitors real-time RMS vibration velocity and provides an analog output of the velocity to the Sensaphone. The sensor comes with a 5m cable and is available with an optional magnetic mounting base. |
 |
4-20mA Type pH Sensor FGD-0305 Monitor pH in a variety of applications. Changes in pH can be critical to water quality. Whether it be in a swimming pool, or more critical applications such water and wastewater treatment facilities, or clean water applications such as laboratories, food and beverage, HVAC systems or healtcare, this integral two-wire 4-20mA pH transmitter can be feed data directly to your Sensaphone device. If set limits are exceeded, the Sensaphone will send alarms to appropriate personnel. The sensor includes a measuring range of 0 to 14pH, replaceable saltbridge for extended service life, flow-thru, hot-tap or submersible mounting, and automatic temperature compensation. |
 |
4-20mA Type ORP Sensor FGD-0315 Oxidation-Reduction Potential (ORP) Sensor. The Sensaphone ORP sensors are dependable industrial grade sensors designed to provide accurate measurement and a long service life under the most demanding conditions. ORP sensors measure of the cleanliness of the water by measuring the contaminants in the water. More contaminants in the water result in less dissolved oxygen because the organics are consuming the oxygen and lower the ORP level. At a higher the ORP level, the water has more ability to destroy foreign contaminants such as microbes, or carbon based contaminants. ORP sensors are often used in aquaculture, HVAC applications, and water purification systems. This integral two-wire 4-20mA ORP transmitter can be feed data directly to your Sensaphone device. If set limits are exceeded, the Sensaphone will send alarms to appropriate personnel. The sensor includes a measuring range of 0 to 1000mV or -500 to 500 mV, replaceable saltbridge for extended service life, flow-thru, hot-tap or submersible mounting, and automatic temperature compensation. |
 |
S4-20 Type Toroidal Conductivity Sensor FGD-0320 Now measure high purity water applications. The Sensaphone Toroidal Conductivity Sensors are used in processes where conventional contacting sensors may become fouled or corroded. These probes are unique in the marketplace. They are loop-powered and provide direct 4-20 mA output. Each sensor comes standard with a Pt100 RTD temperature device, which provides automatic temperature compensation to 25°C (77°F). These sensors are equipped with 1.5” MNPT threads on both ends so that they can be mounted for in-flow applications or submersion mounted in tanks or open vessels. |
 |
4-20 Type Toroidal Conductivity Sensor FGD-0321 Now measure high purity water applications. The Sensaphone Toroidal Conductivity Sensors are used in processes where conventional contacting sensors may become fouled or corroded. These probes are unique in the marketplace. They are loop-powered and provide direct 4-20 mA output. Each sensor comes standard with a Pt100 RTD temperature device, which provides automatic temperature compensation to 25°C (77°F). These sensors are equipped with 1.5” MNPT threads on both ends so that they can be mounted for in-flow applications or submersion mounted in tanks or open vessels. |
 |
4-20 Type Toroidal Conductivity Sensor FGD-0322 Now measure high purity water applications. The Sensaphone Toroidal Conductivity Sensors are used in processes where conventional contacting sensors may become fouled or corroded. These probes are unique in the marketplace. They are loop-powered and provide direct 4-20 mA output. Each sensor comes standard with a Pt100 RTD temperature device, which provides automatic temperature compensation to 25°C (77°F). These sensors are equipped with 1.5” MNPT threads on both ends so that they can be mounted for in-flow applications or submersion mounted in tanks or open vessels. |
 |
External Antenna for Cellular Devices FGD-CELL-ANT Place your cellular Sensaphone in a location that would normally have reduced signal contact. The FGD-CELL-ANT is designed to work with the Sensaphone Sentinel with Cellular Modem. The antenna allows you to place your Sensaphone in a location that would normally have reduced signal contact (such as in a metal cabinet). The antenna comes with 16.3' of cable. |
 |
External High Gain Antenna FGD-CELL-HGANT Increase cell signal strength. The External High Gain Antenna can help to extend the range of the unit's celluar service. Versatile and easy to install, the antenna can be easily mounted on a wall or pole. Ideal for buildings and applications with long cable runs. |
 |
VFC Refrigerator Temperature Sensor with Display The Local Temperature Display also:
|
 |
VFC Refrigerator Temperature Sensor with Display FGD-VFC-GLY The Temperature Sensor Display helps meet compliance when monitoring vaccines for the CDC’s Vaccines For Children (VFC) program. From the factory, the display comes with a NIST certified temperature probe in a glass bead buffered bottle for installation inside of the refrigerator. The display is mounted to the outside of the refrigerator and then connected to a Sensaphone system that is capable of data logging. The Local Temperature Display also:
|
 |
Sensaphone Web600 Battery Backup |
 |
WSG Wireless Water Detection Sensors FGD-WSG30-SPOT Monitor for the presence of water. The WSG30 Wireless Water Detection Sensors are designed to work exclusively with the Sensaphone WSG30. These sensors includes a built-in radio transmitter and water sensing probes for monitoring for the presence of water. The Spot Water Detection sensor will monitor for the presence of water directly under the sensor. The Zone Water Detection sensor connects to a water sensing rope which provides up to 10' of coverage. Up to nine additional lengths of water rope can be added to extend the monitoring area. The sensors comes with three AA alkaline batteries which will power the sensor for up to two years. |
 |
WSG Wireless 4-20mA Sensor |
 |
WSG Wireless Dry Contact Interface FGD-WSG30-DRY Connect to any normally-open or normally closed output. The WSG Wireless Dry Contact sensor is designed to work exclusively with the Sensaphone WSG30. This sensor includes a built-in radio transmitter and input terminals for connecting to any normally-open or normally closed output. (Use of this device with solid-state outputs is not recommended.) The sensor comes with two AA alkaline batteries which will power the sensor for up to two years. An optional plug-in power supply is also available. The batteries then become a backup if main AC power fails. |
 |
WSG Wireless Humidity Sensor FGD-WSG30-HUM Monitor humidity levels. The WSG Wireless Humidity Sensor is designed to work exclusively with the Sensaphone WSG30. This sensor includes a built-in radio transmitter and humidity sensor element for monitoring humidity wherever the device is installed. The sensor comes with two AA alkaline batteries which will power the sensor for up to two years. An optional plug-in power supply is also available. The batteries then become a backup if main AC power fails. |
 |
WSG Wireless Power Failure Sensor FGD-WSG30-PWR Monitor for power loss. The WSG Wireless Power Failure sensor is designed to work exclusively with the Sensaphone WSG30. This sensor includes a built-in radio transmitter, two AA alkaline batteries and a wall plug in power supply. The sensor will detect a loss of power at the outlet where the power supply is attached. The two AA alkaline batteries will power the sensor and allow it to transmit alarm information in the event that 120VAC power fails. |
 |
WSG Wireless Temperature Sensor FGD-WSG30-TMP Easy temperature monitoring. The WSG Wireless Temperature sensor is designed to work exclusively with the Sensaphone WSG30. This sensor includes a built-in radio transmitter and temperature element for monitoring temperature. The sensor is available with either an external temperature probe that will monitor temperatures away from the device, or an internal temperature sensing element for measuring ambient air temperatures. Users can always remove the internal temperature element and attach a remote temperature probe so that measurements can be made in a refrigerator, freezer or other harsh environment. The sensor comes with two AA alkaline batteries which will power the sensor for up to two years. An optional plug-in power supply is also available in which case the batteries become a backup if main AC power fails. |
 |
WSG Wireless Temperature Sensor with External Probe FGD-WSG30-TEX The WSG Wireless Temperature sensor with External Probe is designed to work exclusively with the Sensaphone WSG30. This sensor includes a built-in radio transmitter and a remote temperature probe so that temperature measurements can be made in a refrigerator, freezer or other harsh environments. The sensor comes with two AA alkaline batteries which will power the sensor for up to two years. An optional plug-in power supply is also available in which case the batteries become a backup if main AC power fails. |
|
WSG Wireless Temperature Sensor with External Probe FGD-WSG30-TEX85 The WSG Wireless Temperature sensor with External Probe is designed to work exclusively with the Sensaphone WSG30. This sensor includes a built-in radio transmitter and a remote temperature probe so that temperature measurements can be made in a refrigerator, freezer or other harsh environments. The sensor comes with two AA alkaline batteries which will power the sensor for up to two years. An optional plug-in power supply is also available in which case the batteries become a backup if main AC power fails. |
|
WSG Wireless Temperature Sensor with External Probe FGDWSG30TX85NIST The WSG Wireless Temperature sensor with External Probe is designed to work exclusively with the Sensaphone WSG30. This sensor includes a built-in radio transmitter and a remote temperature probe so that temperature measurements can be made in a refrigerator, freezer or other harsh environments. The sensor comes with two AA alkaline batteries which will power the sensor for up to two years. An optional plug-in power supply is also available in which case the batteries become a backup if main AC power fails. |
|
WSG Wireless Temperature Sensor with External Probe FGDWSG30TEXNIST The WSG Wireless Temperature sensor with External Probe is designed to work exclusively with the Sensaphone WSG30. This sensor includes a built-in radio transmitter and a remote temperature probe so that temperature measurements can be made in a refrigerator, freezer or other harsh environments. The sensor comes with two AA alkaline batteries which will power the sensor for up to two years. An optional plug-in power supply is also available in which case the batteries become a backup if main AC power fails. |
 |
WSG Wireless Temperature Sensor in Buffered Bottle FGD-WSG30-GBV Buffer momentary temperature fluctuations. The Wireless Temperature Sensors are used exclusively with the WSG30 system to measure the temperature of objects in a refrigerator or freezer. By placing the sensor in a bottle filled with glass beads or glycol users will receive a reading that represents the temperature of the contents of inside of the refrigerator rather than the ambient air temperature. When the temperature falls outside of the WSG30 system’s programmed high or low limit, the user will receive an alarm via text message or email. The external probe is wired to the sensor with the included 12’ of wire. The sensor includes two AA alkaline batteries which will power the sensor for up to two years. An optional plug-in power supply is also available, in which case the batteries then become a backup if the main AC power fails. The wireless sensor can be placed up to 300’ away from the WSG30 or further if multiple sensors are used to create a mesh network. |
|
WSG Wireless Temperature Sensor in Buffered Bottle FGDWSG30GBVNIST Buffer momentary temperature fluctuations. The Wireless Temperature Sensors are used exclusively with the WSG30 system to measure the temperature of objects in a refrigerator or freezer. By placing the sensor in a bottle filled with glass beads or glycol users will receive a reading that represents the temperature of the contents of inside of the refrigerator rather than the ambient air temperature. When the temperature falls outside of the WSG30 system’s programmed high or low limit, the user will receive an alarm via text message or email. The external probe is wired to the sensor with the included 12’ of wire. The sensor includes two AA alkaline batteries which will power the sensor for up to two years. An optional plug-in power supply is also available, in which case the batteries then become a backup if the main AC power fails. The wireless sensor can be placed up to 300’ away from the WSG30 or further if multiple sensors are used to create a mesh network. |
|
WSG Wireless Temperature Sensor in Buffered Bottle FGD-WSG30-GLY Buffer momentary temperature fluctuations. The Wireless Temperature Sensors are used exclusively with the WSG30 system to measure the temperature of objects in a refrigerator or freezer. By placing the sensor in a bottle filled with glass beads or glycol users will receive a reading that represents the temperature of the contents of inside of the refrigerator rather than the ambient air temperature. When the temperature falls outside of the WSG30 system’s programmed high or low limit, the user will receive an alarm via text message or email. The external probe is wired to the sensor with the included 12’ of wire. The sensor includes two AA alkaline batteries which will power the sensor for up to two years. An optional plug-in power supply is also available, in which case the batteries then become a backup if the main AC power fails. The wireless sensor can be placed up to 300’ away from the WSG30 or further if multiple sensors are used to create a mesh network. |
|
WSG Wireless Temperature Sensor in Buffered Bottle FGDWSG30GLYNIST Buffer momentary temperature fluctuations. The Wireless Temperature Sensors are used exclusively with the WSG30 system to measure the temperature of objects in a refrigerator or freezer. By placing the sensor in a bottle filled with glass beads or glycol users will receive a reading that represents the temperature of the contents of inside of the refrigerator rather than the ambient air temperature. When the temperature falls outside of the WSG30 system’s programmed high or low limit, the user will receive an alarm via text message or email. The external probe is wired to the sensor with the included 12’ of wire. The sensor includes two AA alkaline batteries which will power the sensor for up to two years. An optional plug-in power supply is also available, in which case the batteries then become a backup if the main AC power fails. The wireless sensor can be placed up to 300’ away from the WSG30 or further if multiple sensors are used to create a mesh network. |
|
WSG Wireless Water Detection Sensors FGD-WSG30-SPOT Monitor for the presence of water. The WSG30 Wireless Water Detection Sensors are designed to work exclusively with the Sensaphone WSG30. These sensors includes a built-in radio transmitter and water sensing probes for monitoring for the presence of water. The Spot Water Detection sensor will monitor for the presence of water directly under the sensor. The Zone Water Detection sensor connects to a water sensing rope which provides up to 10' of coverage. Up to nine additional lengths of water rope can be added to extend the monitoring area. The sensors comes with three AA alkaline batteries which will power the sensor for up to two years. |
 |
IMS-4000 Enterprise Monitoring Node Expansion Unit |
 |
IMS-4000 Dry Contact Node IMS-4010 IMS-4000 Expansion. The IMS-4000 Dry Contact Node provides eight dry contact inputs (normally open/normally closed) and works in conjunction with the IMS Host. The device communicates with the IMS-4000 Host via its Ethernet connection. The Dry Contact Node is a cost-effective solution when your application only requires monitoring of dry contacts. With this device you do not need to use Dry Contact Bridges, thus reducing cost, installation time, and space. This device includes four AA rechargeable NiMH batteries for power backup in the event of a power failure. Both main power and battery charge are monitored and can be programmed to trip alarms as well. The unit comes in a black plastic enclosure with tabs for wall mounting. Rubber feet are also included for placement on a shelf/desktop. |
 |
IMS-4000 Receiver Node For Wireless Sensors
The system uses mesh networking technology to create multiple communication paths between the sensors and the receiver, ensuring reliable communication across all wireless control devices. A battery-powered option is also available for installations where there is no outlet. |
|
IMS-4000 Receiver Node For Wireless Sensors
The system uses mesh networking technology to create multiple communication paths between the sensors and the receiver, ensuring reliable communication across all wireless control devices. A battery-powered option is also available for installations where there is no outlet. |
 |
IMS Wireless Room Temperature Sensor IMS-4210 Easy temperature monitoring. The IMS Wireless Temperature Sensor provides remote temperature monitoring without running wires. Temperature data is sent from the sensor to the IMS-4200 wireless node via an integrated 2.4GHz wireless radio. The device can transmit its signal up to 250′ indoors and even greater distances when it has line-of-site. The IMS series of wireless sensors also features mesh networking technology. With this technology, you can use each sensor as either a wireless sensor/router or as a low-power battery operated sensor (also referred to as an end device). When used as a router, each sensor/router adds another 250′ of range to the system. The sensor comes with 3 AA alkaline batteries, which will power the sensor for up to 2 years (end device mode). An optional plug-in power supply is also available. If the main AC power fails, the batteries function as backup power (power supply required for router mode). |
 |
IMS Wireless Room Temperature Sensor, External Probe IMS-4210-E Easy temperature monitoring. The IMS Wireless Temperature Sensor provides remote temperature monitoring without running wires. Temperature data is sent from the sensor to the IMS-4200 wireless node via an integrated 2.4GHz wireless radio. The device can transmit its signal up to 250′ indoors and even greater distances when it has line-of-site. The IMS series of wireless sensors also features mesh networking technology. With this technology, you can use each sensor as either a wireless sensor/router or as a low-power battery operated sensor (also referred to as an end device). When used as a router, each sensor/router adds another 250′ of range to the system. The sensor comes with 3 AA alkaline batteries, which will power the sensor for up to 2 years (end device mode). An optional plug-in power supply is also available. If the main AC power fails, the batteries function as backup power (power supply required for router mode). |
 |
IMS-4000 Wireless Humidity Sensor IMS-4211 Monitor humidity levels. The IMS-4211 Wireless Humidity sensor provides remote humidity monitoring without running wires. Data is sent from the sensor to the IMS-4200 Wireless Node via an integrated 2.4GHz wireless radio. The device can transmit its signal up to 250′ indoors and even greater distances when it has line-of-site. The IMS series of wireless sensors also feature mesh networking technology, which allows each sensor to be used as either a wireless sensor/router or as a low-power battery operated sensor (also referred to as an end device). When used as a router, greater distances can be realized because each sensor/router adds another 250′ of range to the system. The sensor comes with 3 AA alkaline batteries which will power the sensor for up to 2 years (end device mode). An optional plug-in power supply is also available, in which case the batteries function as backup power if main AC power fails (power supply required for router mode). |
 |
IMS Wireless Dry Contact Interface |
 |
IMS Wireless Power Failure Sensor IMS-4213 Monitor for power loss. The IMS-4213 Wireless Power sensor provides remote power monitoring without running wires. The power status is monitored by the wall plug in adapter and sent from the sensor to the IMS-4200 Wireless Node via an integrated 2.4GHz wireless radio. The device can transmit its signal up to 250′ indoors and even greater distances when it has line-of-site. The IMS series of wireless sensors also feature mesh networking technology, which allows each sensor to be used as either a wireless sensor/router or as a low-power battery operated sensor (also referred to as an end device). When used as a router, greater distances can be realized because each sensor/router adds another 250′ of range to the system. The sensor comes with 3 AA alkaline batteries which will power the sensor for up to 2 years (end device mode). A plug-in power supply is included. The batteries function as backup power when main AC power fail. |
 |
IMS Wireless 4-20mA Interface IMS-4214 Monitor the output of any 4-20mA transducer. The IMS-4214 Wireless 4-20mA sensor provides remote monitoring of 4-20mA transducers without running wires. The 4-20mA signal is sent from the sensor to the IMS-4200 Wireless Node via an integrated 2.4GHz wireless radio. An internal 24V DC supply is built-in to power the current loop. The device can transmit its signal up to 250′ indoors and even greater distances when it has line-of-site. The IMS series of wireless sensors also feature mesh networking technology, which allows each sensor to be used as either a wireless sensor/router or as a lowpower battery operated sensor (also referred to as an end device). When used as a router, greater distances can be realized because each sensor/ router adds another 250′ of range to the system. The sensor comes with 3 AA alkaline batteries which will power the sensor when main power fails. A plug-in power supply is included. |
 |
IMS Wireless Spot Water Detection Sensor IMS-4215 Monitor for the presence of water. The IMS-4215 Wireless Spot Water Detection Sensor provides remote leak detection monitoring without running wires. The sensor has four probes on the bottom of the enclosure which will trigger an alarm when any adjacent pair get wet. Alarm information is sent from the sensor to the IMS-4200 Wireless node via an integrated 2.4GHz Wireless radio. The device can transmit its signal up to 250′ indoors and even greater distances when it has line-of-site. This sensor is battery operated only, and cannot be used as a router. Simply place the sensor on the floor in the area to be monitored. The sensor comes with 3 AA alkaline batteries which will power the sensor for up to 2 years. |
 |
IMS Wireless Zone Water Detection Sensor IMS-4216 Monitor for the presence of water. The IMS-4215 Wireless Zone Water Detection Sensor provides remote leak detection monitoring without running wires. The sensor comes with 10′ of leak detection cable which can be installed around equipment or under a raised flooring system. The detection cable can be extended to cover larger areas by connecting additional 10′ lengths. Alarm information is sent from the sensor to the wireless radio. The device can transmit its signal up to 250′ indoors and even greater distances when it has line-of-site. The IMS series of wireless sensors also feature mesh networking technology, which allows each sensor to be used as either a wireless sensor/router or as a low-power battery operated sensor (also referred to as an end device). When used as a router, greater distances can be realized because each sensor/router adds another 250′ of range to the system. The sensor comes with 3 AA alkaline batteries which will power the sensor for up to 2 years (end device mode). An optional plug-in power supply is also available, in which case the batteries function as backup power if main AC power fails (power supply required for router mode). |
 |
IMS-4000 Dual Relay Output Module IMS-4310 Control two devices from any IMS-4000 Host or Node. The IMS-4310 Dual Relay Output Module allows you to control two devices from any IMS-4000 Host or Node. Each output may be controlled either manually or automatically. Each output has the option of providing either a dry relay contact or 12VDC power. Two switches located inside the device select the output type. |
 |
IMS-4000 DB9 Null Modem Cable IMS-4407 Replacement cable used to connect a computer to an IMS-4000 Host for initial network configuration. |
 |
IP Camera IMS-4424 Receive photo snapshots with your alarms. The Axis camera is a small wireless network camera ideal for monitoring your small business property, data center, or residence. The camera can be used in combination with the IMS-1000 or IMS-4000 systems to send camera snapshots via e-mail when alarms are detected. The camera offers a high quality yet affordable video surveillance solution. Using progressive scan technology, the camera provides VGA images of moving objects without motion blur. Designed to compliment modern interiors and easy to install and use, the camera will not look out of place in the home or office and is ideal for IP camera novices. The Axis IP camera has a built-in web server and can be viewed over a Local Area Network (LAN), Wide Area Network (WAN) or via the Internet as a streaming IP webcam. With this IP camera, you’ll always be able to see exactly what’s going on at your premises – regardless of time of day or lighting. With HDTV 1080p, it delivers excellent image quality. Wide Dynamic Range (WDR) technology ensures you can see details even when there are dark and light areas in the scene. & IR illumination means you can record useful videos even in the dark. |
 |
IMS Solution Indoor Temperature Sensors IMS-4810 Easy temperature monitoring. The line of IMS room temperature sensors will connect to any Sensaphone IMS series product to measure indoor temperatures. The electrical connection between the sensor and IMS unit is made via RJ-45 patch cable (not included). Mount the sensor to a single-gang electrical box to directly to a wall. The connection from the sensor to the Host or Node can use your existing network wiring infrastructure, so you can install the sensor in another room or floor. You can also connect the sensor to your structured wiring network via an RJ-45 jack. Choose between a local display with values displayed in °F, °C or no local display. |
|
IMS Solution Indoor Temperature Sensors IMS-4811 Easy temperature monitoring. The line of IMS room temperature sensors will connect to any Sensaphone IMS series product to measure indoor temperatures. The electrical connection between the sensor and IMS unit is made via RJ-45 patch cable (not included). Mount the sensor to a single-gang electrical box to directly to a wall. The connection from the sensor to the Host or Node can use your existing network wiring infrastructure, so you can install the sensor in another room or floor. You can also connect the sensor to your structured wiring network via an RJ-45 jack. Choose between a local display with values displayed in °F, °C or no local display. |
 |
IMS Solution Mini Temperature Sensor IMS-4812 Monitor temperature in tight locations. The IMS-4812 Mini Temperature Sensor is designed to connect to the Sensaphone IMS series product line and monitor temperatures in tight locations (for example, inside equipment racks). The electrical connection between the sensor and IMS unit is made via the attached RJ-45 patch cable. The sensor may be secured inside equipment using double-sided tape (included) or with tie-wraps. The Mini-Temperature Sensor comes with an attached 7′ cable with a RJ-45 plug on the end. If the sensor is close to the IMS unit, you can plug the sensor directly to an IMS environmental input. If the cable is too short you can use the included RJ-45 adaptor and a longer patch cable to extend the length. For applications where the sensor may be far from the IMS unit, you may utilize your existing network wiring infrastructure. For example, the sensor may be installed in another room or another floor. Connect the sensor to your structured wiring network via an RJ-45 jack. At the other end, connect a patch cable from your structured wiring patch panel directly to the Host or Node environmental input. |
|
IMS Solution Indoor Temperature Sensors IMS-4813 Easy temperature monitoring. The line of IMS room temperature sensors will connect to any Sensaphone IMS series product to measure indoor temperatures. The electrical connection between the sensor and IMS unit is made via RJ-45 patch cable (not included). Mount the sensor to a single-gang electrical box to directly to a wall. The connection from the sensor to the Host or Node can use your existing network wiring infrastructure, so you can install the sensor in another room or floor. You can also connect the sensor to your structured wiring network via an RJ-45 jack. Choose between a local display with values displayed in °F, °C or no local display. |
 |
IMS Solution Ultra Low Temperature Sensor IMS-4814 Monitor temperatures as low as -85°C. The IMS-4814 Ultra Low Temperature Sensor is designed to connect to the Sensaphone IMS product line and monitor temperatures in refrigerators or freezers. The electrical connection between the sensor and IMS unit is made via the attached RJ-45 patch cable. The sensor probe may be secured inside equipment using the included clamp or it may be hung using tie wraps. Do not install the black plastic enclosure inside of a refrigerator or freezer. This sensor includes a remote temperature probe so that temperature measurements can be made in a refrigerator, freezer or other harsh environments. The sensor is availabe with an optional glass bead vial which helps to prevent false tempearture readings when a refrigerator or freezer door is opened or goes into a defrost cycle. In addition they are available with an optional NIST temperature certification. The Ultra Low Temperature Sensors comes with an attached 7′ cable with an RJ-45 plug on the end and a weatherproof probe with 12′ of cable. If the sensor installation is close to the IMS unit, you can plug it directly into an IMS environmental input. If the cable is too short you can use the included RJ-45 adaptor and a longer patch cable to extend the length. For applications where the sensor may be far from the IMS unit, you may utilize your existing network wiring infrastructure. For example, the sensor may be installed in another room or another floor. Connect the sensor to your structured wiring network via an RJ-45 jack. At the other end, connect a patch cable from your structured wiring patch panel directly to the Host or Node environment input. NIST temperature certification is available. |
 |
IMS Solution Ultra Low Temperature Sensor IMS-4815 Monitor temperatures as low as -85°C. The IMS-4814 Ultra Low Temperature Sensor is designed to connect to the Sensaphone IMS product line and monitor temperatures in refrigerators or freezers. The electrical connection between the sensor and IMS unit is made via the attached RJ-45 patch cable. The sensor probe may be secured inside equipment using the included clamp or it may be hung using tie wraps. Do not install the black plastic enclosure inside of a refrigerator or freezer. This sensor includes a remote temperature probe so that temperature measurements can be made in a refrigerator, freezer or other harsh environments. The sensor is availabe with an optional glass bead vial which helps to prevent false tempearture readings when a refrigerator or freezer door is opened or goes into a defrost cycle. In addition they are available with an optional NIST temperature certification. The Ultra Low Temperature Sensors comes with an attached 7′ cable with an RJ-45 plug on the end and a weatherproof probe with 12′ of cable. If the sensor installation is close to the IMS unit, you can plug it directly into an IMS environmental input. If the cable is too short you can use the included RJ-45 adaptor and a longer patch cable to extend the length. For applications where the sensor may be far from the IMS unit, you may utilize your existing network wiring infrastructure. For example, the sensor may be installed in another room or another floor. Connect the sensor to your structured wiring network via an RJ-45 jack. At the other end, connect a patch cable from your structured wiring patch panel directly to the Host or Node environment input. NIST temperature certification is available. |
 |
IMS Solution Temperature Sensor w/ External Probe IMS-4816 Easy temperature monitoring. The IMS-4816 Temperature Sensor with External Probe is designed to connect to the Sensaphone IMS product line and monitor temperatures in areas where a traditional sensor won't fit. The electrical connection between the sensor and IMS unit is made via the attached RJ-45 patch cable. The sensor probe may be secured inside equipment using the included clamp or it may be hung using tie wraps. Do not install the black plastic enclosure inside of a refrigerator or freezer. The Temperature Sensor with External Probe comes with an attached 7′ cable with an RJ-45 plug on the end and a weatherproof probe with 12′ of cable. If the sensor installation is close to the IMS unit, you can plug it directly into an IMS environmental input. If the cable is too short you can use the included RJ-45 adaptor and a longer patch cable to extend the length. For applications where the sensor may be far from the IMS unit, you may utilize your existing network wiring infrastructure. For example, the sensor may be installed in another room or another floor. Connect the sensor to your structured wiring network via an RJ-45 jack. At the other end, connect a patch cable from your structured wiring patch panel directly to the Host or Node environment input. |
 |
IMS Solution Room Humidity Sensor IMS-4820 Monitor humidity levels The IMS humidity sensors are designed to connect to the Sensaphone IMS series product line and monitor indoor humidity levels. The sensor is available with or without a local display. The electrical connection between the sensor and IMS unit is made via RJ-45 patch cable (not included). The sensor may be mounted either on a wall or to a single-gang electrical box. The connection from the sensor to the Host or Node can utilize your existing network wiring infrastructure. For example, the sensor may be installed in another room or another floor. Connect the sensor to your structured wiring network via an RJ-45 jack. At the other end, connect a patch cable from your structured wiring patch panel directly to the Host or Node environmental input. |
 |
IMS Humidity Sensor w/LCD Readout |
 |
IMS Solution Zone Water Detection Sensor IMS-4830 Widespread water detection. The IMS-4830 Water Detection sensor protects your server and equipment from damaging water leaks from malfunctioning HVAC systems, cafeteria accidents, or any general plumbing failures in your facilities. The IMS-4830 is powered directly by the IMS unit. After mounting the sensor, attach the included 10′ of WaterRope, and simply lay the orange cable around your equipment: place it on the floor or beneath a raised floor; inside a dropceiling or in the rafters between floors; or anywhere you must know about water near your equipment. You can attach up to nine additional Water Ropes to expand your water leak detection capabilities throughout your facility. |
 |
Extra 10′ Water Detection Rope IMS-4831 Widespread water detection. The IMS-4830 Water Detection sensor protects your server and equipment from damaging water leaks from malfunctioning HVAC systems, cafeteria accidents, or any general plumbing failures in your facilities. The IMS-4830 is powered directly by the IMS unit. After mounting the sensor, attach the included 10′ of WaterRope, and simply lay the orange cable around your equipment: place it on the floor or beneath a raised floor; inside a dropceiling or in the rafters between floors; or anywhere you must know about water near your equipment. You can attach up to nine additional Water Ropes to expand your water leak detection capabilities throughout your facility. |
 |
IMS Solution External Power Failure Sensor IMS-4840 Power monitoring. The IMS-4840 External Power Sensor lets you monitor power anywhere within your infrastructure. It reports any loss of power and measures the current voltage in the circuit, allowing you to know the status of each server rack and even your remote UPS. Any failed generator starts are reported to you immediately. The IMS-4840 can monitor voltage from 0-250VAC 50/60Hz. The Power Sensor connects to the IMS Host or Node via an RJ-45 cable (e.g. CAT5 cable). The connection from the sensor to the Host or Node can utilize your existing network wiring infrastructure. For example, the sensor may be installed in another room or another floor. Connect the sensor to your structured wiring network via an RJ-45 jack. At the other end, connect a patch cable from your structured wiring patch panel directly to the Host or Node environmental input.. |
 |
IMS Solution Current Sensor IMS-4841 Current consumption monitoring. The IMS Current Sensors lets you monitor current consumption of a particular device or circuit anywhere within your infrastructure. It reports the actual current flow in the circuit, allowing you to know the current draw from devices such as server racks, UPS and generators. Any failed generator starts are reported to you immediately. The IMS-4841 can monitor current from 0-15 amps over a voltage range from 0-250VAC 50/60Hz and comes with IEC320 C14 inlet and C13 outlet connectors. The IMS-4842 monitors current from from 0-20 Amps over a voltage range from 0–250VAC 50/60Hz and comes with IEC320 C20 inlet and C19 outlet connectors. |
 |
IMS Solution Current Sensor IMS-4842 Current consumption monitoring. The IMS Current Sensors lets you monitor current consumption of a particular device or circuit anywhere within your infrastructure. It reports the actual current flow in the circuit, allowing you to know the current draw from devices such as server racks, UPS and generators. Any failed generator starts are reported to you immediately. The IMS-4841 can monitor current from 0-15 amps over a voltage range from 0-250VAC 50/60Hz and comes with IEC320 C14 inlet and C13 outlet connectors. The IMS-4842 monitors current from from 0-20 Amps over a voltage range from 0–250VAC 50/60Hz and comes with IEC320 C20 inlet and C19 outlet connectors. |
 |
IMS Solution Dry Contact Interface IMS-4850 Connect to any NO/NC Contact. The IMS-4850 Dry Contact Bridge allows you to connect a dry contact alarm from any device to your IMS. The Dry Contact Bridge is compatible with Normally Open and Normally Closed contacts. The electrical connection between the sensor and IMS is made via RJ-45 patch cable (not included). The sensor may be mounted either on a wall or rest on the floor. The Dry Contact Bridge connects to the IMS via a RJ-45 cable (e.g. CAT5 cable). The connection from the sensor to the Host or Node can utilize your existing network wiring infrastructure. For example, the sensor may be installed in another room or another floor. Connect the bridge to your structured wiring network via a RJ-45 jack. At the other end, connect a patch cable from your structured wiring patch panel directly to the Host or Node environmental input. |
 |
IMS Solution 4-20mA Interface |
 |
IMS Solution Magnetic Reed Door and Window Switch IMS-4860 Detect unauthorized entry or intrusion. The IMS-4860 Door and Window Switch with bridge enables your IMS unit to detect if any unauthorized entry or intrusion has occurred. The bridge may be mounted either on a wall or rest on the floor. The switch is mounted to doors or windows you wish to monitor. The electrical connection between the bridge and IMS unit is made via RJ-45 patch cable. The connection from the bridge to Host or Node can utilize your existing network wiring infrastructure. For example, the switch may be installed in another room or another floor. Connect the bridge to your structured wiring network via an RJ-45 jack. At the other end, connect a patch cable from your structured wiring patch panel directly to the Host or Node environmental input. |
 |
IMS Solution Infrared Motion Detection Sensor IMS-4861 Monitor for the movement of warm bodies. The IMS-4861 Infrared Detection sensor is a dual-element passive infrared intrusion detector for use in electronic security systems. It reduces FALSE alarms by eliminating background noises and nuisance stimuli. The IMS-4861 employs variable pulse-count adjustment, thus making it adaptable for use both inside and outside of server/equipment rooms. It is designed to connect to the IMS Host or Node. The Infrared Detection Sensor comes with an attached 7′ cable with an RJ-45 plug on the end. If the sensor is close to the IMS Host or Node, you can plug the sensor directly to an IMS environmental input. If the cable is too short you can use the included RJ-45 adaptor and a longer patch cable to extend the length. |
 |
IMS Solution Smoke Detection Sensor IMS-4862 Smoke detection. The IMS-4862 Smoke Detection sensor is designed to connect to the IMS Host or Node and monitor for smoke in indoor environments. The electrical connection between the sensor and IMS is made via the attached RJ-45 patch cable. The sensor may be secured to a wall or ceiling (hardware not included). If the sensor is close to the IMS Host or Node, you can plug the sensor directly to an IMS environmental input. If the cable is too short you can use the included RJ-45 adaptor and a longer patch cable to extend the length. For applications where the sensor may be far from the IMS unit, you may utilize your existing network wiring infrastructure. For example, the sensor may be installed in another room or another floor. Connect the sensor to your structured wiring network via an RJ-45 jack. At the other end, connect a patch cable from your structured wiring patch panel directly to the Host or Node environment input. |
 |
IMS Solution Air Flow Sensor IMS-4863 Monitor the presence or absence of cool moving air. The Air Flow sensor is designed to monitor for the presence or absence of cool moving air. This is especially useful for monitoring air conditioning systems. The sensor can provide relative air flow as a percentage from 0 to 100. The sensor is compatible with both the IMS-1000 and IMS-4000 devices. The Air Flow sensor connects to the IMS via a RJ-45 cable (e.g. CAT5 cable). The connection from the sensor to the Host or Node can utilize your existing network wiring infrastructure. For example, the sensor may be installed in another room or another floor. Connect the bridge to your structured wiring network via a RJ-45 jack. At the other end, connect a patch cable from your structured wiring patch panel directly to the Host or Node environmental input. |
 |
Wireless Zone Water Detection Sensor WSR-0107 The WSR-0107 Wireless Zone Water Detection Sensor is designed to work with the Sensaphone 2800 Environmental Monitoring System. This sensor includes a built-in radio transmitter and ten feet of water sensing cable for monitoring for the presence of water in a particular area. The size of the monitored area can be extended by attaching additional lengths of WaterRope (FGD-0063) to the end of the included WaterRope. You can connect up to ten lengths of WaterRope (100′) to one Zone Water Detector. The sensor comes with 3 AA alkaline batteries which will power the sensor for up to 3 years. |
 |
12VDC Power Supply Accessory for Dual Setback Thermostat |
Sensaphone 400 and Accessories |
||
Sensaphone 400 Products |
Part # |
Price |
| Sensaphone Model 400 | FGD-0400 | $387.00 |
| Sensaphone Model 400 w/ International Power Supply | FGD-0400-INT | $404.10 |
Sensaphone 400 Accessories |
Part # |
Price |
| Contact Type Magnetic Reed Door and Window Switch | FGD-0006 | $9.00 |
| Contact Type Infrared Motion Detection Sensor | FGD-0007-HW | $71.10 |
| 50 Feet Coil of Accessory Wire | FGD-0010 | $16.00 |
| 500 Feet Reel of Accessory Wire | FGD-0010-500 | $119.00 |
| Contact Type Spot Water Detection Sensor | FGD-0013 | $81.00 |
| Contact Type Temp Alert Temperature Switch | FGD-0022 | $99.00 |
| Contact Type Humidistat Humidity Switch | FGD-0027 | $55.00 |
| Contact Type Smoke Detector Sensor for 110VAC w/Battery Backup | FGD-0049-B | $72.00 |
| Contact Type PowerOut Alert Power Failure Switch | FGD-0054 | $89.00 |
| Contact Type Zone Water Detection Sensor | FGD-0056 | $126.00 |
| Water Rope Extension for Zone Water Detectors | FGD-0063 | $81.00 |
| Dual Setback Thermostat | FGD-0064 | $120.00 |
| Surge Suppressor Accessory for Power & Phone | FGD-0067 | $24.99 |
| 2.8K Type Room Temperature Sensor | FGD-0100 | $27.00 |
| 2.8K Type Weatherproof Temperature Sensor | FGD-0101 | $27.00 |
| 2.8K Type Weatherproof Temp Sensor w/NIST Certificate | FGD-0101-NIST | $117.00 |
| 2.8K Type Ultra Low -85C Temp Sensor w/Teflon Cable | FGD-0101-TEF | $45.00 |
| 2.8K Type Ultra Low -85C Temp w/Teflon Cable & NIST Certificate | FGD-0101TEFNIST | $135.00 |
| 2.8K Type Temperature Sensor in Glass Bead Vial | FGD-0107 | $49.50 |
| 2.8K Type Temperature Sensor in Glass Bead Vial & NIST Certificate | FGD-0107-NIST | $139.50 |
| 2.8K Type Ultra Low Temperature Sensor w/Teflon Cable | FGD-0107-TEF | $67.50 |
| 2.8K Type Ultra Low Temperature Sensor w/Teflon Cable & NIST Certificate | FGD-0107TEFNiST | $157.50 |
| LCD Readout for 2.8K Type Temperature Sensor | FGD-0120 | $116.99 |
| 2.8K Type Temperature Sensor in Glycol Vial | FGD-0127 | $49.50 |
| 2.8K Type Temperature Sensor in Glycol Vial & NIST | FGD-0127-NIST | $139.50 |
| 2.8K Type Ultra Low Temperature Sensor in Glycol Vial w/Teflon Cable | FGD-0127-TEF | $67.50 |
| 2.8K Type Ultra Low Temperature Sensor in Glycol Vial w/Teflon Cable & NIST Certificate | FGD-0127TEFNIST | $157.50 |
| Contact Type Float Level Switch | FGD-0222 | $35.10 |
| Temp probe w/Glass Bead Vial, NIST Certificate and LCD Readout | FGD-VFC-GBV | $224.99 |
| Temp probe w/Glycol Vial, NIST Certificate and LCD Readout | FGD-VFC-GLY | $224.99 |
| 12VDC Power Supply Accessory for Dual Setback Thermostat | XFR-0024 | $15.00 |
Sensaphone 800 and Accessories |
||
Sensaphone 800 Products |
Part # |
Price |
| Sensaphone Model 800 | FGD-0800 | $567.00 |
| Sensaphone Model 800 w/ International Power Supply | FGD-0800-INT | $584.10 |
Sensaphone 800 Accessories |
Part # |
Price |
| Contact Type Magnetic Reed Door and Window Switch | FGD-0006 | $9.00 |
| Contact Type Infrared Motion Detection Sensor | FGD-0007-HW | $71.10 |
| 50 Feet Coil of Accessory Wire | FGD-0010 | $16.00 |
| 500 Feet Reel of Accessory Wire | FGD-0010-500 | $119.00 |
| Contact Type Spot Water Detection Sensor | FGD-0013 | $81.00 |
| Contact Type Temp Alert Temperature Switch | FGD-0022 | $99.00 |
| Contact Type Humidistat Humidity Switch | FGD-0027 | $55.00 |
| Contact Type Smoke Detector Sensor for 110VAC w/Battery Backup | FGD-0049-B | $72.00 |
| Contact Type PowerOut Alert Power Failure Switch | FGD-0054 | $89.00 |
| Contact Type Zone Water Detection Sensor | FGD-0056 | $126.00 |
| Water Rope Extension for Zone Water Detectors | FGD-0063 | $81.00 |
| Dual Setback Thermostat | FGD-0064 | $120.00 |
| Surge Suppressor Accessory for Power & Phone | FGD-0067 | $24.99 |
| 2.8K Type Room Temperature Sensor | FGD-0100 | $27.00 |
| 2.8K Type Weatherproof Temperature Sensor | FGD-0101 | $27.00 |
| 2.8K Type Weatherproof Temp Sensor w/NIST Certificate | FGD-0101-NIST | $117.00 |
| 2.8K Type Ultra Low -85C Temp Sensor w/Teflon Cable | FGD-0101-TEF | $45.00 |
| 2.8K Type Ultra Low -85C Temp w/Teflon Cable & NIST Certificate | FGD-0101TEFNIST | $135.00 |
| 2.8K Type Temperature Sensor in Glass Bead Vial | FGD-0107 | $49.50 |
| 2.8K Type Temperature Sensor in Glass Bead Vial & NIST Certificate | FGD-0107-NIST | $139.50 |
| 2.8K Type Ultra Low Temperature Sensor w/Teflon Cable | FGD-0107-TEF | $67.50 |
| 2.8K Type Ultra Low Temperature Sensor w/Teflon Cable & NIST Certificate | FGD-0107TEFNiST | $157.50 |
| LCD Readout for 2.8K Type Temperature Sensor | FGD-0120 | $116.99 |
| 2.8K Type Temperature Sensor in Glycol Vial | FGD-0127 | $49.50 |
| 2.8K Type Temperature Sensor in Glycol Vial & NIST | FGD-0127-NIST | $139.50 |
| 2.8K Type Ultra Low Temperature Sensor in Glycol Vial w/Teflon Cable | FGD-0127-TEF | $67.50 |
| 2.8K Type Ultra Low Temperature Sensor in Glycol Vial w/Teflon Cable & NIST Certificate | FGD-0127TEFNIST | $157.50 |
| Contact Type Float Level Switch | FGD-0222 | $35.10 |
| Temp probe w/Glass Bead Vial, NIST Certificate and LCD Readout | FGD-VFC-GBV | $224.99 |
| Temp probe w/Glycol Vial, NIST Certificate and LCD Readout | FGD-VFC-GLY | $224.99 |
| 12VDC Power Supply Accessory for Dual Setback Thermostat | XFR-0024 | $15.00 |
Sensaphone 1400 and Accessories |
||
Sensaphone Model 1400 Products |
Part # |
Price |
| Sensaphone 1400 w/ Clear Door | FGD-1400-CD | $764.10 |
| Sensaphone 1400 Monitoring System w/ NEMA 4X Clear Door for 220VAC | FGD-1400-CD-INT | $782.10 |
| Sensaphone 1400 Monitoring System w/ NEMA 4X Solid Door Enclosure | FGD-1400-SD | $764.10 |
| Sensaphone 1400 Monitoring System w/ NEMA 4X Solid Door for 220VAC | FGD-1400-SD-INT | $782.10 |
Sensaphone Model 1400 Accessories |
Part # |
Price |
| Contact Type Magnetic Reed Door and Window Switch | FGD-0006 | $9.00 |
| Contact Type Infrared Motion Detection Sensor | FGD-0007-HW | $71.10 |
| 50 Feet Coil of Accessory Wire | FGD-0010 | $16.00 |
| 500 Feet Reel of Accessory Wire | FGD-0010-500 | $119.00 |
| Contact Type Spot Water Detection Sensor | FGD-0013 | $81.00 |
| Contact Type Temp Alert Temperature Switch | FGD-0022 | $99.00 |
| Contact Type Humidistat Humidity Switch | FGD-0027 | $55.00 |
| Contact Type Smoke Detector Sensor for 110VAC w/Battery Backup | FGD-0049-B | $72.00 |
| Humidity 4-20mA Transmitter | FGD-0052 | $143.10 |
| 4-20mA Outdoor Humidity Sensor | FGD-0052-OD | $179.10 |
| 4-20mA Duct Mount Humidity Transmitter | FGD-0052-DUCT | $206.10 |
| 24VDC Power Supply for 4-20mA Sensors | FGD-0053 | $41.39 |
| Contact Type PowerOut Alert Power Failure Switch | FGD-0054 | $89.00 |
| Telephone Adapter UK | FGD-0055 | $5.00 |
| Contact Type Zone Water Detection Sensor | FGD-0056 | $126.00 |
| External Microphone Attachment | FGD-0057 | $27.00 |
| Outdoor 4-20mA Dewpoint | FGD-0059-OD | $278.10 |
| Water Rope Extension for Zone Water Detectors | FGD-0063 | $81.00 |
| Carbon Monoxide Detector | FGD-0065 | $299.00 |
| Surge Suppressor Accessory for Power & Phone | FGD-0067 | $24.99 |
| Carbon Dioxide Sensor | FGD-0068 | $309.00 |
| Carbon Dioxide Duct Mount Transmitter | FGD-0068-DUCT | $359.10 |
| 4-20mA Type Outdoor CO2 Transmitter | FGD-0068-OD | $539.10 |
| 4-20mA Type 0-20k CO2 Transmitter | FGD-0068-20K | $405.00 |
| 4-20mA Type Duct Mount Air Flow Transmitter | FGD-0069-DUCT | $202.50 |
| 24VDC Power Supply Accessory for 4-20mA Sensors w/ Battery Backup | FGD-0070 | $107.10 |
| 24VDC Power Supply Accessory for 4-20mA Sensors w/Battery Backup International | FGD-0070-INT | $125.10 |
| 24VDC Power Supply DIN Rail | FGD-0071 | $90.00 |
| 50A Split Core Current Sensor | FGD-0075-50 | $103.50 |
| 200A Split Core Current Sensor | FGD-0075-200 | $117.00 |
| 4-20mA Type Soil Moisture Sensor | FGD-0090 | $235.00 |
| 2.8K Type Room Temperature Sensor | FGD-0100 | $27.00 |
| 2.8K Type Weatherproof Temperature Sensor | FGD-0101 | $27.00 |
| 2.8K Type Weatherproof Temp Sensor w/NIST Certificate | FGD-0101-NIST | $117.00 |
| 2.8K Type Ultra Low -85C Temp Sensor w/Teflon Cable | FGD-0101-TEF | $45.00 |
| 2.8K Type Ultra Low -85C Temp w/Teflon Cable & NIST Certificate | FGD-0101TEFNIST | $135.00 |
| 2.8K Type Temperature Sensor in Glass Bead Vial | FGD-0107 | $49.50 |
| 2.8K Type Temperature Sensor in Glass Bead Vial & NIST Certificate | FGD-0107-NIST | $139.50 |
| 2.8K Type Ultra Low Temperature Sensor w/Teflon Cable | FGD-0107-TEF | $67.50 |
| 2.8K Type Ultra Low Temperature Sensor w/Teflon Cable & NIST Certificate | FGD-0107TEFNiST | $157.50 |
| LCD Readout for 2.8K Type Temperature Sensor | FGD-0120 | $116.99 |
| 2.8K Type Temperature Sensor in Glycol Vial | FGD-0127 | $49.50 |
| 2.8K Type Temperature Sensor in Glycol Vial & NIST | FGD-0127-NIST | $139.50 |
| 2.8K Type Ultra Low Temperature Sensor in Glycol Vial w/Teflon Cable | FGD-0127-TEF | $67.50 |
| 2.8K Type Ultra Low Temperature Sensor in Glycol Vial w/Teflon Cable & NIST Certificate | FGD-0127TEFNIST | $157.50 |
| J Type Thermocouple/4-20mA Converter | FGD-0220 | $399.00 |
| Contact Type Float Level Switch | FGD-0222 | $35.10 |
| 4-20mA Type Dual Flow & Temperature Sensor - 1" Probe | FGD-0223-1 | $445.00 |
| 4-20mA Type Dual Flow & Temperature Sensor - 4" Probe | FGD-0223-4 | $449.00 |
| RTD probe w/4-20mA Transmitter (-200 to 35 C) | FGD-0240 | $285.00 |
| RTD probe w/4-20mA Transmitter (-200 to 204 C) | FGD-0240-SPEC | $310.00 |
| 14" RTD Probe with 4-20mA | FGD-0240-14 | $285.00 |
| RTD probe w/4-20mA Transmitter (User Specified Range) | FGD-0240-14SPEC | $310.00 |
| 4-20mA Type Pressure Sensor | FGD-0301 | $149.00 |
| Differential Pressure Duct Sensor | FGD-0302-DUCT | $314.10 |
| 4-20mA Type Differential Pressure Sensor with Wall Mount Kit | FGD-0302-ROOM | $314.10 |
| 4-20mA Type Vibration Sensor | FGD-0303 | $349.00 |
| 4-20mA Type Vibration Sensor Mount | FGD-0303-MOUNT | $63.00 |
| 4-20mA Type pH Sensor | FGD-0305 | Call for Pricing |
| 4-20mA Type ORP Sensor | FGD-0315 | Call for Pricing |
| 4-20 Type Toroidal Conductivity Sensor, 0-10mS | FGD-0320 | Call for Pricing |
| 4-20 Type Toroidal Conductivity Sensor, 0-100mS | FGD-0321 | Call for Pricing |
| 4-20 Type Toroidal Conductivity Sensor, 0-1000mS | FGD-0322 | Call for Pricing |
| Dissolved Oxygen Transducer | FGD-0325 | Call for Pricing |
| Temp probe w/Glycol Vial, NIST and LCD Readout | FGD-VFC-GLY | $224.99 |
| Temp probe w/Glass Bead Vial, NIST and LCD Readout | FGD-VFC-GBV | $224.99 |
Sensaphone 1800 and Accessories |
||
Sensaphone Model 1800 Products |
Part # |
Price |
| Sensaphone 1800 w/ Clear Door | FGD-1800-CD | $1,012.50 |
| Sensaphone 1800 Monitoring System w/ NEMA 4X Clear Door for 220VAC | FGD-1800-CD-INT | $1,030.50 |
| Sensaphone 1800 Monitoring System w/ NEMA 4X Solid Door Enclosure | FGD-1800-SD | $1,012.50 |
| Sensaphone 1800 Monitoring System w/ NEMA 4X Solid Door for 220VAC | FGD-1800-SD-INT | $1,030.50 |
Sensaphone Model 1800 Accessories |
Part # |
Price |
| Contact Type Magnetic Reed Door and Window Switch | FGD-0006 | $9.00 |
| Contact Type Infrared Motion Detection Sensor | FGD-0007-HW | $71.10 |
| 50 Feet Coil of Accessory Wire | FGD-0010 | $16.00 |
| 500 Feet Reel of Accessory Wire | FGD-0010-500 | $119.00 |
| Contact Type Spot Water Detection Sensor | FGD-0013 | $81.00 |
| Contact Type Temp Alert Temperature Switch | FGD-0022 | $99.00 |
| Contact Type Humidistat Humidity Switch | FGD-0027 | $55.00 |
| Contact Type Smoke Detector Sensor for 110VAC w/Battery Backup | FGD-0049-B | $72.00 |
| Humidity 4-20mA Transmitter | FGD-0052 | $143.10 |
| 4-20mA Outdoor Humidity Sensor | FGD-0052-OD | $179.10 |
| 4-20mA Duct Mount Humidity Transmitter | FGD-0052-DUCT | $206.10 |
| 24VDC Power Supply for 4-20mA Sensors | FGD-0053 | $41.39 |
| Contact Type PowerOut Alert Power Failure Switch | FGD-0054 | $89.00 |
| Telephone Adapter UK | FGD-0055 | $5.00 |
| Contact Type Zone Water Detection Sensor | FGD-0056 | $126.00 |
| External Microphone Attachment | FGD-0057 | $27.00 |
| Outdoor 4-20mA Dewpoint | FGD-0059-OD | $278.10 |
| Water Rope Extension for Zone Water Detectors | FGD-0063 | $81.00 |
| Carbon Monoxide Detector | FGD-0065 | $299.00 |
| Mini Surge Protector - Power and Phone | FGD-0067 | $24.99 |
| Carbon Dioxide Sensor | FGD-0068 | $309.00 |
| Carbon Dioxide Duct Mount Transmitter | FGD-0068-DUCT | $359.10 |
| 4-20mA Type Outdoor CO2 Transmitter | FGD-0068-OD | $539.10 |
| 4-20mA Type 0-20k CO2 Transmitter | FGD-0068-20K | $405.00 |
| 4-20mA Type Duct Mount Air Flow Transmitter | FGD-0069-DUCT | $202.50 |
| 24VDC Power Supply Accessory for 4-20mA Sensors w/ Battery Backup | FGD-0070 | $107.10 |
| 24VDC Power Supply Accessory for 4-20mA Sensors w/Battery Backup International | FGD-0070-INT | $125.10 |
| 24VDC Power Supply DIN Rail | FGD-0071 | $90.00 |
| 50A Split Core Current Sensor | FGD-0075-50 | $103.50 |
| 200A Split Core Current Sensor | FGD-0075-200 | $117.00 |
| 4-20mA Type Soil Moisture Sensor | FGD-0090 | $235.00 |
| 2.8K Type Room Temperature Sensor | FGD-0100 | $27.00 |
| 2.8K Type Weatherproof Temperature Sensor | FGD-0101 | $27.00 |
| 2.8K Type Weatherproof Temp Sensor w/NIST Certificate | FGD-0101-NIST | $117.00 |
| 2.8K Type Ultra Low -85C Temp Sensor w/Teflon Cable | FGD-0101-TEF | $45.00 |
| 2.8K Type Ultra Low -85C Temp w/Teflon Cable & NIST Certificate | FGD-0101TEFNIST | $135.00 |
| 2.8K Type Temperature Sensor in Glass Bead Vial | FGD-0107 | $49.50 |
| 2.8K Type Temperature Sensor in Glass Bead Vial & NIST Certificate | FGD-0107-NIST | $139.50 |
| 2.8K Type Ultra Low Temperature Sensor w/Teflon Cable | FGD-0107-TEF | $67.50 |
| 2.8K Type Ultra Low Temperature Sensor w/Teflon Cable & NIST Certificate | FGD-0107TEFNiST | $157.50 |
| LCD Readout for 2.8K Type Temperature Sensor | FGD-0120 | $116.99 |
| 2.8K Type Temperature Sensor in Glycol Vial | FGD-0127 | $49.50 |
| 2.8K Type Temperature Sensor in Glycol Vial & NIST | FGD-0127-NIST | $139.50 |
| 2.8K Type Ultra Low Temperature Sensor in Glycol Vial w/Teflon Cable | FGD-0127-TEF | $67.50 |
| 2.8K Type Ultra Low Temperature Sensor in Glycol Vial w/Teflon Cable & NIST Certificate | FGD-0127TEFNIST | $157.50 |
| J Type Thermocouple/4-20mA Converter | FGD-0220 | $399.00 |
| USB to RS-232 Serial Converter Accessory | FGD-0221 | $30.00 |
| Contact Type Float Level Switch | FGD-0222 | $35.10 |
| 4-20mA Type Dual Flow & Temperature Sensor - 1" Probe | FGD-0223-1 | $445.00 |
| 4-20mA Type Dual Flow & Temperature Sensor - 4" Probe | FGD-0223-4 | $449.00 |
| RTD probe w/4-20mA Transmitter (-200 to 35 C) | FGD-0240 | $285.00 |
| RTD probe w/4-20mA Transmitter (-200 to 204 C) | FGD-0240-SPEC | $310.00 |
| 14" RTD Probe with 4-20mA | FGD-0240-14 | $285.00 |
| RTD probe w/4-20mA Transmitter (User Specified Range) | FGD-0240-14SPEC | $310.00 |
| Ethernet to WiFi Adapter | FGD-0250 | $119.00 |
| Ethernet to WiFi Adapter Accessory | FGD-0250-U | $119.00 |
| 4-20mA Type Pressure Sensor | FGD-0301 | $149.00 |
| Differential Pressure Duct Sensor | FGD-0302-DUCT | $314.10 |
| 4-20mA Type Differential Pressure Sensor with Wall Mount Kit | FGD-0302-ROOM | $314.10 |
| 4-20mA Type Vibration Sensor | FGD-0303 | $349.00 |
| 4-20mA Type Vibration Sensor Mount | FGD-0303-MOUNT | $63.00 |
| 4-20mA Type pH Sensor | FGD-0305 | Call for Pricing |
| 4-20mA Type ORP Sensor | FGD-0315 | Call for Pricing |
| 4-20 Type Toroidal Conductivity Sensor, 0-10mS | FGD-0320 | Call for Pricing |
| 4-20 Type Toroidal Conductivity Sensor, 0-100mS | FGD-0321 | Call for Pricing |
| 4-20 Type Toroidal Conductivity Sensor, 0-1000mS | FGD-0322 | Call for Pricing |
| Dissolved Oxygen Transducer | FGD-0325 | Call for Pricing |
| Temp probe w/Glycol Vial, NIST and LCD Readout | FGD-VFC-GLY | $224.99 |
| Temp probe w/Glass Bead Vial, NIST and LCD Readout | FGD-VFC-GBV | $224.99 |
Sensaphone WSG30 and Accessories |
||
Sensaphone Model WSG30 |
Part # |
Price |
| Sensaphone WSG30 Wireless Sensor Gateway | FGD-WSG30 | $751.50 |
| Sensaphone WSG30 Wireless Sensor Gateway For 220VAC | FGD-WSG30-INT | $769.50 |
Sensaphone Model WSG30 Accessories |
Part # |
Price |
| Mini Surge Protector - Power and Phone | FGD-0067 | $24.99 |
| Ethernet to WiFi Adapter | FGD-0250 | $119.00 |
| Ethernet to WiFi Adapter Accessory | FGD-0250-U | $119.00 |
| WSG Wireless Temperture Sensor | FGD-WSG30-TMP | $170.10 |
| WSG Wireless Temp w/ External Probe | FGD-WSG30-TEX | $179.10 |
| WSG Wireless Temperature Sensor w/External Probe & NIST Certificate | FGDWSG30TEXNIST | $269.10 |
| WSG Wireless Ultra Low Temperature Sensor w/External Probe & Teflon Cable | FGD-WSG30-TEX85 | $197.10 |
| WSG Wireless Ultra Low Temperature Sensor w/External Probe & Teflon Cable & NIST Certificate | FGDWSG30TX85NST | $287.10 |
| WSG Wireless Temperature Sensor w/Glass Bead Vial | FGD-WSG30-GBV | $211.50 |
| WSG Wireless Temp w/Glass Bead & NIST | FGDWSG30GBVNIST | $301.50 |
| WSG Wireless Temp Sensor in Glycol Vial | FGD-WSG30-GLY | $211.50 |
| WSG Wireless Temp Sensor in Glycol Vial with NIST Certificate | FGDWSG30GLYNIST | $301.50 |
| WSG Wireless Humidity Sensor | FGD-WSG30-HUM | $215.10 |
| WSG Wireless Dry Contact Sensor | FGD-WSG30-DRY | $170.10 |
| WSG Wireless Power Failure Sensor | FGD-WSG30-PWR | $179.10 |
| WSG 4-20mA Wireless Interface | FGD-WSG30-4-20 | $233.10 |
| WSG Wireless Spot Water Detection Sensor | FGD-WSG30-SPOT | $224.10 |
| WSG Wireless Zone Water Detection Sensor | FGD-WSG30-ZONE | $237.60 |
| Power Supply for WSG30 Wireless Sensors | XFR-0041 | $15.00 |
| Power Supply for WSG30 Wireless Zone Water Sensor Only | XFR-0046 | $15.00 |
| Power Supply for WSG30 Wireless Sensor Gateway | XFR-0047 | $15.00 |
| Power Supply for WSG30 Wireless Sensors for 220VAC | XFR-0048 | $15.00 |
Sensaphone EXPRESS II and Accessories |
||
Sensaphone EXPRESS II |
Part # |
Price |
| Sensaphone Express II | FGD-6700 | $1,863.00 |
Sensaphone EXPRESS II Accessories |
Part # |
Price |
| Contact Type Magnetic Reed Door and Window Switch | FGD-0006 | $9.00 |
| Contact Type Infrared Motion Detection Sensor | FGD-0007-HW | $71.10 |
| 50 Feet Coil of Accessory Wire | FGD-0010 | $16.00 |
| 500 Feet Reel of Accessory Wire | FGD-0010-500 | $119.00 |
| Contact Type Spot Water Detection Sensor | FGD-0013 | $81.00 |
| Contact Type Temp Alert Temperature Switch | FGD-0022 | $99.00 |
| Contact Type Humidistat Humidity Switch | FGD-0027 | $55.00 |
| Express II 8 Input Card Slot 2 | FGD-0035 | $369.00 |
| Express II 8 Input Card Slot 3 | FGD-0036 | $369.00 |
| Express II 8 Input Card Slot 4 | FGD-0037 | $369.00 |
| Express II 8 Input Card Slot 5 | FGD-0038 | $369.00 |
| Express II 8 Output Card Slot 1 | FGD-0040 | $369.00 |
| Express II 8 Output Card Slot 2 | FGD-0041 | $369.00 |
| Contact Type Smoke Detector Sensor for 110VAC w/Battery Backup | FGD-0049-B | $72.00 |
| Humidity 4-20mA Transmitter | FGD-0052 | $143.10 |
| 4-20mA Outdoor Humidity Sensor | FGD-0052-OD | $179.10 |
| 4-20mA Duct Mount Humidity Transmitter | FGD-0052-DUCT | $206.10 |
| 24VDC Power Supply for 4-20mA Sensors | FGD-0053 | $41.39 |
| Contact Type PowerOut Alert Power Failure Switch | FGD-0054 | $89.00 |
| Telephone Adapter UK | FGD-0055 | $5.00 |
| Contact Type Zone Water Detection Sensor | FGD-0056 | $126.00 |
| External Microphone Attachment | FGD-0057 | $27.00 |
| Water Rope Extension for Zone Water Detectors | FGD-0063 | $81.00 |
| Carbon Monoxide Detector | FGD-0065 | $299.00 |
| Mini Surge Protector - Power and Phone | FGD-0067 | $24.99 |
| Carbon Dioxide Sensor | FGD-0068 | $309.00 |
| Carbon Dioxide Duct Mount Transmitter | FGD-0068-DUCT | $359.10 |
| 4-20mA Type Outdoor CO2 Transmitter | FGD-0068-OD | $539.10 |
| 4-20mA Type 0-20k CO2 Transmitter | FGD-0068-20K | $405.00 |
| 4-20mA Type Duct Mount Air Flow Transmitter | FGD-0069-DUCT | $202.50 |
| 24VDC Power Supply Accessory for 4-20mA Sensors w/ Battery Backup | FGD-0070 | $107.10 |
| 24VDC Power Supply Accessory for 4-20mA Sensors w/Battery Backup International | FGD-0070-INT | $125.10 |
| 24VDC Power Supply DIN Rail | FGD-0071 | $90.00 |
| 50A Split Core Current Sensor | FGD-0075-50 | $103.50 |
| 200A Split Core Current Sensor | FGD-0075-200 | $117.00 |
| 4-20mA Type Soil Moisture Sensor | FGD-0090 | $235.00 |
| 2.8K Type Room Temperature Sensor | FGD-0100 | $27.00 |
| 2.8K Type Weatherproof Temperature Sensor | FGD-0101 | $27.00 |
| 2.8K Type Weatherproof Temp Sensor w/NIST Certificate | FGD-0101-NIST | $117.00 |
| 2.8K Type Ultra Low -85C Temp Sensor w/Teflon Cable | FGD-0101-TEF | $45.00 |
| 2.8K Type Ultra Low -85C Temp w/Teflon Cable & NIST Certificate | FGD-0101TEFNIST | $135.00 |
| 10K Weatherproof Temperature Sensor | FGD-0102 | $27.00 |
| 10K Weatherproof Temperature Sensor - NIST | FGD-0102-NIST | $117.00 |
| 10 K Indoor Decorator Zone Temperature Sensor | FGD-0103 | $36.00 |
| 10K Outdoor Air Weatherproof Temperature Sensor | FGD-0104 | $63.00 |
| 10K Immersion Temperature Sensor | FGD-0105 | $65.00 |
| 2.8K Type Temperature Sensor in Glass Bead Vial | FGD-0107 | $49.50 |
| 2.8K Type Temperature Sensor in Glass Bead Vial & NIST Certificate | FGD-0107-NIST | $139.50 |
| 2.8K Type Ultra Low Temperature Sensor w/Teflon Cable | FGD-0107-TEF | $67.50 |
| 2.8K Type Ultra Low Temperature Sensor w/Teflon Cable & NIST Certificate | FGD-0107TEFNiST | $157.50 |
| LCD Readout for 2.8K Type Temperature Sensor | FGD-0120 | $116.99 |
| 2.8K Type Temperature Sensor in Glycol Vial | FGD-0127 | $49.50 |
| 2.8K Type Temperature Sensor in Glycol Vial & NIST | FGD-0127-NIST | $139.50 |
| 2.8K Type Ultra Low Temperature Sensor in Glycol Vial w/Teflon Cable | FGD-0127-TEF | $67.50 |
| 2.8K Type Ultra Low Temperature Sensor in Glycol Vial w/Teflon Cable & NIST Certificate | FGD-0127TEFNIST | $157.50 |
| J Type Thermocouple/4-20mA Converter | FGD-0220 | $399.00 |
| Contact Type Float Level Switch | FGD-0222 | $35.10 |
| 4-20mA Type Dual Flow & Temperature Sensor - 1" Probe | FGD-0223-1 | $445.00 |
| 4-20mA Type Dual Flow & Temperature Sensor - 4" Probe | FGD-0223-4 | $449.00 |
| RTD probe w/4-20mA Transmitter (-200 to 35 C) | FGD-0240 | $285.00 |
| RTD probe w/4-20mA Transmitter (-200 to 204 C) | FGD-0240-SPEC | $310.00 |
| 14" RTD Probe with 4-20mA | FGD-0240-14 | $285.00 |
| RTD probe w/4-20mA Transmitter (User Specified Range) | FGD-0240-14SPEC | $310.00 |
| 4-20mA Type Pressure Sensor | FGD-0301 | $149.00 |
| Differential Pressure Duct Sensor | FGD-0302-DUCT | $314.10 |
| 4-20mA Type Differential Pressure Sensor with Wall Mount Kit | FGD-0302-ROOM | $314.10 |
| 4-20mA Type Vibration Sensor | FGD-0303 | $349.00 |
| 4-20mA Type Vibration Sensor Mount | FGD-0303-MOUNT | $63.00 |
| 4-20mA Type pH Sensor | FGD-0305 | Call for Pricing |
| 4-20mA Type ORP Sensor | FGD-0315 | Call for Pricing |
| 4-20 Type Toroidal Conductivity Sensor, 0-10mS | FGD-0320 | Call for Pricing |
| 4-20 Type Toroidal Conductivity Sensor, 0-100mS | FGD-0321 | Call for Pricing |
| 4-20 Type Toroidal Conductivity Sensor, 0-1000mS | FGD-0322 | Call for Pricing |
| Dissolved Oxygen Transducer | FGD-0325 | Call for Pricing |
| Temp probe w/Glycol Vial, NIST and LCD Readout | FGD-VFC-GLY | $224.99 |
| Temp probe w/Glass Bead Vial, NIST and LCD Readout | FGD-VFC-GBV | $224.99 |
Sensaphone SAT4D and Accessories |
||
Sensaphone Model SAT4D Accessories |
Part # |
Price |
| Contact Type Magnetic Reed Door and Window Switch | FGD-0006 | $9.00 |
| Contact Type Infrared Motion Detection Sensor | FGD-0007-HW | $71.10 |
| 50 Feet Coil of Accessory Wire | FGD-0010 | $16.00 |
| 500 Feet Reel of Accessory Wire | FGD-0010-500 | $119.00 |
| Contact Type Spot Water Detection Sensor | FGD-0013 | $81.00 |
| Contact Type Temp Alert Temperature Switch | FGD-0022 | $99.00 |
| Contact Type Humidistat Humidity Switch | FGD-0027 | $55.00 |
| Contact Type Smoke Detector Sensor for 110VAC w/Battery Backup | FGD-0049-B | $72.00 |
| PowerOut Alert MODEL PS-110 | FGD-0054 | $89.00 |
| Zone Water Detector | FGD-0056 | $126.00 |
| Water Rope Extension for Zone Water Detectors | FGD-0063 | $81.00 |
| Mini Surge Protector - Power and Phone | FGD-0067 | $24.99 |
| J Type Thermocouple/4-20mA Converter | FGD-0220 | $399.00 |
| Sensaphone SAT4D One Year Communication Service | FGD-SAT1Y | $420.00 |
Sensaphone Sentinel and Accessories |
||
Sensaphone Sentinel |
Part # |
Price |
| Sensaphone Sentinel Monitoring System Solid Door | SCD-1200 | $553.50 |
| Sensaphone Sentinel Monitoring System Clear Door | SCD-1200-CD | $746.10 |
| Sensaphone Sentinel Standard Ethernet Version w/Clear Door 220VAC | SCD-1200-CD-INT | $768.60 |
| Sensaphone Sentinel Standard Ethernet Version w/Solid Door | SCD-1200-SD | $746.10 |
| Sensaphone Sentinel Standard Ethernet Version w/Solid Door 220VAC | SCD-1200-SD-INT | $768.60 |
| Sensaphone Sentinel Standard Ethernet Version 220V | SCD-1200-INT | $571.50 |
| 1 Month Sentinel Premium Ethernet Subscription | SCD-1200-1METH | $6.95 |
| 1 Year Sentinel Premium Ethernet Subscription | SCD-1200-1YETH | $83.40 |
| Sentinel w/AT&T Cellular Modem Clear Door | SCD-1200-4GATCD | $1,561.50 |
| Sentinel w/AT&T Cellular Modem Solid Door | SCD-1200-4GATSD | $1,561.50 |
| Sentinel w/Verizon Cellular Modem Clear Door | SCD-1200-4GVZCD | $1,561.50 |
| Sentinel w/Verizon Cellular Modem Solid Door | SCD-1200-4GVZSD | $1,561.50 |
| Sentinel w/Rogers Wireless Clear Door | SCD-1200-4GRWCD | $1,561.50 |
| Sentinel w/Rogers Wireleess Solid Door | SCD-1200-4GRWSD | $1,561.50 |
| 1 Month Sentinel Cellular Subscription | SCD-1200-1MCELL | $24.95 |
| 1 Year Sentinel Cellular Subscription | SCD-1200-1YCELL | $299.40 |
| Sensaphone Sentinel Pro | SCD-PRO | $1,169.10 |
| Sensaphone Sentinel Pro w/International Power Supply | SCD-PRO-INT | $1,188.00 |
| Sensaphone Sentinel Pro Nema-4X Clear Door | SCD-PRO-CD | $1,345.50 |
| Sensaphone Sentinel Pro Nema-4X Clear Door w/International Power Supply | SCD-PRO-CD-INT | $1,363.50 |
| Sensaphone Sentinel Pro Nema-4X Solid Door | SCD-PRO-SD | $1,345.50 |
| Sensaphone Sentinel Pro Nema-4X Solid Door w/International Power Supply | SCD-PRO-SD-INT | $1,363.50 |
| Sentinel Pro 1 Month Premium Ethernet Subscription | SCD-PRO-1METH | $10.95 |
| Sentinel Pro 1 Year Premium Ethernet Subscription | SCD-PRO-1YETH | $131.40 |
| Sentinel Pro 4G AT&T Cellular Modem Clear Door | SCD-PRO-4GATCD | $1,921.50 |
| Sentinel Pro 4G AT&T Cellular Modem Solid Door | SCD-PRO-4GATSD | $1,921.50 |
| Sentinel Pro 4G Verizon Cellular Modem Clear Door | SCD-PRO-4GVZCD | $1,921.50 |
| Sentinel Pro 4G Verizon Cellular Modem Solid Door | SCD-PRO-4GVZSD | $1,921.50 |
| Sentinel Pro 4G Rogers Cellular Modem Clear Door | SCD-PRO-4GRWCD | $1,921.50 |
| Sentinel Pro 4G Rogers Cellular Modem Solid Door | SCD-PRO-4GRWSD | $1,921.50 |
| Sentinel Pro 1 Month Cellular Subscription | SCD-PRO-1MCELL | $34.95 |
| Sentinel Pro 1 Year Cellular Subscription | SCD-PRO-1YCELL | $419.40 |
| AT&T Cell Modem for Cloud | FGD-4GLTE-AT | $1,163.30 |
| Rogers Cell Modem for Cloud | FGD-4GLTE-RW | $1,163.30 |
| Verizon Cell Modem for Cloud | FGD-4GLTE-VZ | $1,163.30 |
Sensaphone Sentinel Accessories |
Part # |
Price |
| Contact Type Magnetic Reed Door and Window Switch | FGD-0006 | $9.00 |
| Contact Type Infrared Motion Detection Sensor | FGD-0007-HW | $71.10 |
| 50 Feet Coil of Accessory Wire | FGD-0010 | $16.00 |
| 500 Feet Reel of Accessory Wire | FGD-0010-500 | $119.00 |
| Contact Type Spot Water Detection Sensor | FGD-0013 | $81.00 |
| Contact Type Temp Alert Temperature Switch | FGD-0022 | $99.00 |
| Contact Type Humidistat Humidity Switch | FGD-0027 | $55.00 |
| Contact Type Smoke Detector Sensor for 110VAC w/Battery Backup | FGD-0049-B | $72.00 |
| Humidity 4-20mA Transmitter | FGD-0052 | $143.10 |
| 4-20mA Outdoor Humidity Sensor | FGD-0052-OD | $179.10 |
| 4-20mA Duct Mount Humidity Transmitter | FGD-0052-DUCT | $206.10 |
| 24VDC Power Supply for 4-20mA Sensors | FGD-0053 | $41.39 |
| Contact Type PowerOut Alert Power Failure Switch | FGD-0054 | $89.00 |
| Telephone Adapter UK | FGD-0055 | $5.00 |
| Contact Type Zone Water Detection Sensor | FGD-0056 | $126.00 |
| Water Rope Extension for Zone Water Detectors | FGD-0063 | $81.00 |
| Carbon Monoxide Detector | FGD-0065 | $299.00 |
| Mini Surge Protector - Power and Phone | FGD-0067 | $24.99 |
| Carbon Dioxide Sensor | FGD-0068 | $309.00 |
| Carbon Dioxide Duct Mount Transmitter | FGD-0068-DUCT | $359.10 |
| 4-20mA Type Outdoor CO2 Transmitter | FGD-0068-OD | $539.10 |
| 4-20mA Type 0-20k CO2 Transmitter | FGD-0068-20K | $405.00 |
| 4-20mA Type Duct Mount Air Flow Transmitter | FGD-0069-DUCT | $202.50 |
| 24VDC Power Supply Accessory for 4-20mA Sensors w/ Battery Backup | FGD-0070 | $107.10 |
| 24VDC Power Supply Accessory for 4-20mA Sensors w/Battery Backup International | FGD-0070-INT | $125.10 |
| 24VDC Power Supply DIN Rail | FGD-0071 | $90.00 |
| 50A Split Core Current Sensor | FGD-0075-50 | $103.50 |
| 200A Split Core Current Sensor | FGD-0075-200 | $117.00 |
| 4-20mA Type Soil Moisture Sensor | FGD-0090 | $235.00 |
| 2.8K Type Room Temperature Sensor | FGD-0100 | $27.00 |
| 2.8K Type Weatherproof Temperature Sensor | FGD-0101 | $27.00 |
| 2.8K Type Weatherproof Temp Sensor w/NIST Certificate | FGD-0101-NIST | $117.00 |
| 2.8K Type Ultra Low -85C Temp Sensor w/Teflon Cable | FGD-0101-TEF | $45.00 |
| 2.8K Type Ultra Low -85C Temp w/Teflon Cable & NIST Certificate | FGD-0101TEFNIST | $135.00 |
| 10K Weatherproof Temperature Sensor | FGD-0102 | $27.00 |
| 10K Weatherproof Temperature Sensor - NIST | FGD-0102-NIST | $117.00 |
| 10 K Indoor Decorator Zone Temperature Sensor | FGD-0103 | $36.00 |
| 10K Outdoor Air Weatherproof Temperature Sensor | FGD-0104 | $63.00 |
| 10K Immersion Temperature Sensor | FGD-0105 | $65.00 |
| 2.8K Type Temperature Sensor in Glass Bead Vial | FGD-0107 | $49.50 |
| 2.8K Type Temperature Sensor in Glass Bead Vial & NIST Certificate | FGD-0107-NIST | $139.50 |
| 2.8K Type Ultra Low Temperature Sensor w/Teflon Cable | FGD-0107-TEF | $67.50 |
| 2.8K Type Ultra Low Temperature Sensor w/Teflon Cable & NIST Certificate | FGD-0107TEFNiST | $157.50 |
| Modbus Temperature/Humidity | FGD-0110 | $206.10 |
| LCD Readout for 2.8K Type Temperature Sensor | FGD-0120 | $116.99 |
| 2.8K Type Temperature Sensor in Glycol Vial | FGD-0127 | $49.50 |
| 2.8K Type Temperature Sensor in Glycol Vial & NIST | FGD-0127-NIST | $139.50 |
| 2.8K Type Ultra Low Temperature Sensor in Glycol Vial w/Teflon Cable | FGD-0127-TEF | $67.50 |
| 2.8K Type Ultra Low Temperature Sensor in Glycol Vial w/Teflon Cable & NIST Certificate | FGD-0127TEFNIST | $157.50 |
| J Type Thermocouple/4-20mA Converter | FGD-0220 | $399.00 |
| Contact Type Float Level Switch | FGD-0222 | $35.10 |
| 4-20mA Type Dual Flow & Temperature Sensor - 1" Probe | FGD-0223-1 | $445.00 |
| 4-20mA Type Dual Flow & Temperature Sensor - 4" Probe | FGD-0223-4 | $449.00 |
| RTD probe w/4-20mA Transmitter (-200 to 35 C) | FGD-0240 | $285.00 |
| RTD probe w/4-20mA Transmitter (-200 to 204 C) | FGD-0240-SPEC | $310.00 |
| 14" RTD Probe with 4-20mA | FGD-0240-14 | $285.00 |
| RTD probe w/4-20mA Transmitter (User Specified Range) | FGD-0240-14SPEC | $310.00 |
| Ethernet to WiFi Adapter | FGD-0250 | $119.00 |
| Ethernet to WiFi Adapter Accessory | FGD-0250-U | $119.00 |
| 4G/LTE External High Gain Antenna | FGD-0260 | $269.99 |
| 3G/4G/LTE External Antenna | FGD-0261 | $59.95 |
| 4-20mA Type Pressure Sensor | FGD-0301 | $149.00 |
| Differential Pressure Duct Sensor | FGD-0302-DUCT | $314.10 |
| 4-20mA Type Differential Pressure Sensor with Wall Mount Kit | FGD-0302-ROOM | $314.10 |
| 4-20mA Type Vibration Sensor | FGD-0303 | $349.00 |
| 4-20mA Type Vibration Sensor Mount | FGD-0303-MOUNT | $63.00 |
| 4-20mA Type pH Sensor | FGD-0305 | Call for Pricing |
| 4-20mA Type ORP Sensor | FGD-0315 | Call for Pricing |
| 4-20 Type Toroidal Conductivity Sensor, 0-10mS | FGD-0320 | Call for Pricing |
| 4-20 Type Toroidal Conductivity Sensor, 0-100mS | FGD-0321 | Call for Pricing |
| 4-20 Type Toroidal Conductivity Sensor, 0-1000mS | FGD-0322 | Call for Pricing |
| Dissolved Oxygen Transducer | FGD-0325 | Call for Pricing |
| Temp probe w/Glass Bead Vial, NIST and LCD Readout | FGD-VFC-GBV | $224.99 |
| Temp probe w/Glycol Vial, NIST and LCD Readout | FGD-VFC-GLY | $224.99 |
| AT&T Cell Modem for Cloud | FGD-4GLTE-AT | $1,075.50 |
| Rogers Cell Modem for Cloud | FGD-4GLTE-RW | $1,075.50 |
| Verizon Cell Modem for Cloud | FGD-4GLTE-VZ | $1,075.50 |
Sensaphone Stratus EMS and Accessories |
||
Sensaphone Stratus EMS |
Part # |
Price |
| Sensaphone Stratus EMS Monitoring System | EMS-7600 | $1,570.50 |
| 1 Month Stratus EMS Premium Ethernet Connection | EMS-7600-1METH | $14.95 |
| 1 Year Stratus EMS Premium Ethernet Connection | EMS-7600-1YETH | $179.40 |
| 1 Month Stratus EMS Cellular Subscription | EMS-7600-1MCELL | $39.95 |
| 1 Year Stratus EMS Cellular Subscription | EMS-7600-1YCELL | $479.40 |
Sensaphone Stratus EMS Accessories |
Part # |
Price |
| Contact Type Magnetic Reed Door and Window Switch | FGD-0006 | $9.00 |
| Contact Type Infrared Motion Detection Sensor | FGD-0007-HW | $71.10 |
| 50 Feet Coil of Accessory Wire | FGD-0010 | $16.00 |
| 500 Feet Reel of Accessory Wire | FGD-0010-500 | $119.00 |
| Contact Type Spot Water Detection Sensor | FGD-0013 | $81.00 |
| Contact Type Temp Alert Temperature Switch | FGD-0022 | $99.00 |
| Contact Type Humidistat Humidity Switch | FGD-0027 | $55.00 |
| Contact Type Smoke Detector Sensor for 110VAC w/Battery Backup | FGD-0049-B | $72.00 |
| Contact Type Smoke Detector Sensor for 220VAC | FGD-0049-220V | $69.00 |
| Humidity 4-20mA Transmitter | FGD-0052 | $143.10 |
| 4-20mA Outdoor Humidity Sensor | FGD-0052-OD | $179.10 |
| 4-20mA Duct Mount Humidity Transmitter | FGD-0052-DUCT | $206.10 |
| 24VDC Power Supply for 4-20mA Sensors | FGD-0053 | $41.39 |
| Contact Type PowerOut Alert Power Failure Switch | FGD-0054 | $89.00 |
| Telephone Adapter UK | FGD-0055 | $5.00 |
| Contact Type Zone Water Detection Sensor | FGD-0056 | $126.00 |
| Water Rope Extension for Zone Water Detectors | FGD-0063 | $81.00 |
| Carbon Monoxide Detector | FGD-0065 | $299.00 |
| Mini Surge Protector - Power and Phone | FGD-0067 | $24.99 |
| Carbon Dioxide Sensor | FGD-0068 | $309.00 |
| Carbon Dioxide Duct Mount Transmitter | FGD-0068-DUCT | $359.10 |
| 4-20mA Type Outdoor CO2 Transmitter | FGD-0068-OD | $539.10 |
| 4-20mA Type 0-20k CO2 Transmitter | FGD-0068-20K | $405.00 |
| 4-20mA Type Duct Mount Air Flow Transmitter | FGD-0069-DUCT | $202.50 |
| 24VDC Power Supply Accessory for 4-20mA Sensors w/ Battery Backup | FGD-0070 | $107.10 |
| 24VDC Power Supply Accessory for 4-20mA Sensors w/Battery Backup International | FGD-0070-INT | $125.10 |
| 24VDC Power Supply DIN Rail | FGD-0071 | $90.00 |
| 50A Split Core Current Sensor | FGD-0075-50 | $103.50 |
| 200A Split Core Current Sensor | FGD-0075-200 | $117.00 |
| 4-20mA Type Soil Moisture Sensor | FGD-0090 | $235.00 |
| 2.8K Type Room Temperature Sensor | FGD-0100 | $27.00 |
| 2.8K Type Weatherproof Temperature Sensor | FGD-0101 | $27.00 |
| 2.8K Type Weatherproof Temp Sensor w/NIST Certificate | FGD-0101-NIST | $117.00 |
| 2.8K Type Ultra Low -85C Temp Sensor w/Teflon Cable | FGD-0101-TEF | $45.00 |
| 2.8K Type Ultra Low -85C Temp w/Teflon Cable & NIST Certificate | FGD-0101TEFNIST | $135.00 |
| 10K Weatherproof Temperature Sensor | FGD-0102 | $27.00 |
| 10K Weatherproof Temperature Sensor - NIST | FGD-0102-NIST | $117.00 |
| 10 K Indoor Decorator Zone Temperature Sensor | FGD-0103 | $36.00 |
| 10K Outdoor Air Weatherproof Temperature Sensor | FGD-0104 | $63.00 |
| 10K Immersion Temperature Sensor | FGD-0105 | $65.00 |
| 2.8K Type Temperature Sensor in Glass Bead Vial | FGD-0107 | $49.50 |
| 2.8K Type Temperature Sensor in Glass Bead Vial & NIST Certificate | FGD-0107-NIST | $139.50 |
| 2.8K Type Ultra Low Temperature Sensor w/Teflon Cable | FGD-0107-TEF | $67.50 |
| 2.8K Type Ultra Low Temperature Sensor w/Teflon Cable & NIST Certificate | FGD-0107TEFNiST | $157.50 |
| Modbus Temperature/Humidity | FGD-0110 | $206.10 |
| 4-20mA Temp/Humidity,CO2 Combo Transmiter | FGD-0111 | $499.00 |
| Modbus Temp/Humidity, CO2 combo Transmitter | FGD-0111-MB | $599.00 |
| LCD Readout for 2.8K Type Temperature Sensor | FGD-0120 | $116.99 |
| 2.8K Type Temperature Sensor in Glycol Vial | FGD-0127 | $49.50 |
| 2.8K Type Temperature Sensor in Glycol Vial & NIST | FGD-0127-NIST | $139.50 |
| 2.8K Type Ultra Low Temperature Sensor in Glycol Vial w/Teflon Cable | FGD-0127-TEF | $67.50 |
| 2.8K Type Ultra Low Temperature Sensor in Glycol Vial w/Teflon Cable & NIST Certificate | FGD-0127TEFNIST | $157.50 |
| J Type Thermocouple/4-20mA Converter | FGD-0220 | $399.00 |
| Contact Type Float Level Switch | FGD-0222 | $35.10 |
| 4-20mA Type Dual Flow & Temperature Sensor - 1" Probe | FGD-0223-1 | $445.00 |
| 4-20mA Type Dual Flow & Temperature Sensor - 4" Probe | FGD-0223-4 | $449.00 |
| RTD probe w/4-20mA Transmitter (-200 to 35 C) | FGD-0240 | $285.00 |
| RTD probe w/4-20mA Transmitter (-200 to 204 C) | FGD-0240-SPEC | $310.00 |
| 14" RTD Probe with 4-20mA | FGD-0240-14 | $285.00 |
| RTD probe w/4-20mA Transmitter (User Specified Range) | FGD-0240-14SPEC | $310.00 |
| Ethernet to WiFi Adapter Accessory | FGD-0250-U | $119.00 |
| 4G/LTE External High Gain Antenna | FGD-0260 | $269.99 |
| 3G/4G/LTE External Antenna | FGD-0261 | $59.95 |
| 4-20mA Type Pressure Sensor | FGD-0301 | $149.00 |
| Differential Pressure Duct Sensor | FGD-0302-DUCT | $314.10 |
| 4-20mA Type Differential Pressure Sensor with Wall Mount Kit | FGD-0302-ROOM | $314.10 |
| 4-20mA Type Vibration Sensor | FGD-0303 | $349.00 |
| 4-20mA Type Vibration Sensor Mount | FGD-0303-MOUNT | $63.00 |
| 4-20mA Type pH Sensor | FGD-0305 | Call for Pricing |
| 4-20mA Type ORP Sensor | FGD-0315 | Call for Pricing |
| 4-20 Type Toroidal Conductivity Sensor, 0-10mS | FGD-0320 | Call for Pricing |
| 4-20 Type Toroidal Conductivity Sensor, 0-100mS | FGD-0321 | Call for Pricing |
| 4-20 Type Toroidal Conductivity Sensor, 0-1000mS | FGD-0322 | Call for Pricing |
| Dissolved Oxygen Transducer | FGD-0325 | Call for Pricing |
| Temp probe w/Glycol Vial, NIST and LCD Readout | FGD-VFC-GLY | $224.99 |
| Temp probe w/Glass Bead Vial, NIST and LCD Readout | FGD-VFC-GBV | $224.99 |
| AT&T Cell Modem for Cloud | FGD-4GLTE-AT | $1,075.50 |
| Rogers Cell Modem for Cloud | FGD-4GLTE-RW | $1,075.50 |
| Verizon Cell Modem for Cloud | FGD-4GLTE-VZ | $1,075.50 |
Sensaphone Carbon and Accessories |
||
Sensaphone Carbon |
Part # |
Price |
| Sensaphone Carbon Monoxide (CO) Sensor | FGD-0065 | $299.00 |
Sensaphone Carbon Accessories |
Part # |
Price |
| 50 Feet Coil of Accessory Wire | FGD-0010 | $16.00 |
| 24VDC Power Supply for 4-20mA Sensors | FGD-0053 | $41.39 |
| 24VDC Power Supply Accessory for 4-20mA Sensors w/ Battery Backup | FGD-0070 | $107.10 |
Sensaphone Web600 and Accessories |
||
Sensaphone Web600 Product |
Part # |
Price |
| Sensaphone Web600 | FGD-W600 | $391.50 |
| Sensaphone Web600, 220VAC | FGD-W600-INT | $409.50 |
Sensaphone Web600 Accessories |
Part # |
Price |
| Web600 Battery Backup | FGD-W610-B | $67.50 |
| Contact Type Magnetic Reed Door and Window Switch | FGD-0006 | $9.00 |
| Contact Type Infrared Motion Detection Sensor | FGD-0007-HW | $71.10 |
| 50 Feet Coil of Accessory Wire | FGD-0010 | $16.00 |
| 500 Feet Reel of Accessory Wire | FGD-0010-500 | $119.00 |
| Contact Type Spot Water Detection Sensor | FGD-0013 | $81.00 |
| Contact Type Temp Alert Temperature Switch | FGD-0022 | $99.00 |
| Contact Type Humidistat Humidity Switch | FGD-0027 | $55.00 |
| Contact Type Smoke Detector Sensor for 110VAC w/Battery Backup | FGD-0049-B | $72.00 |
| Contact Type Smoke Detector Sensor for 220VAC | FGD-0049-220V | $69.00 |
| Humidity 4-20mA Transmitter | FGD-0052 | $143.10 |
| 4-20mA Outdoor Humidity Sensor | FGD-0052-OD | $179.10 |
| 4-20mA Duct Mount Humidity Transmitter | FGD-0052-DUCT | $206.10 |
| 24VDC Power Supply for 4-20mA Sensors | FGD-0053 | $41.39 |
| Contact Type PowerOut Alert Power Failure Switch | FGD-0054 | $89.00 |
| Telephone Adapter UK | FGD-0055 | $5.00 |
| Contact Type Zone Water Detection Sensor | FGD-0056 | $126.00 |
| Water Rope Extension for Zone Water Detectors | FGD-0063 | $81.00 |
| Carbon Monoxide Detector | FGD-0065 | $299.00 |
| Mini Surge Protector - Power and Phone | FGD-0067 | $24.99 |
| Carbon Dioxide Sensor | FGD-0068 | $309.00 |
| Carbon Dioxide Duct Mount Transmitter | FGD-0068-DUCT | $359.10 |
| 4-20mA Type Outdoor CO2 Transmitter | FGD-0068-OD | $539.10 |
| 4-20mA Type 0-20k CO2 Transmitter | FGD-0068-20K | $405.00 |
| 4-20mA Type Duct Mount Air Flow Transmitter | FGD-0069-DUCT | $202.50 |
| 24VDC Power Supply Accessory for 4-20mA Sensors w/ Battery Backup | FGD-0070 | $107.10 |
| 24VDC Power Supply Accessory for 4-20mA Sensors w/Battery Backup International | FGD-0070-INT | $125.10 |
| 24VDC Power Supply DIN Rail | FGD-0071 | $90.00 |
| 50A Split Core Current Sensor | FGD-0075-50 | $103.50 |
| 200A Split Core Current Sensor | FGD-0075-200 | $117.00 |
| 4-20mA Type Soil Moisture Sensor | FGD-0090 | $235.00 |
| 2.8K Type Room Temperature Sensor | FGD-0100 | $27.00 |
| 2.8K Type Weatherproof Temperature Sensor | FGD-0101 | $27.00 |
| 2.8K Type Weatherproof Temp Sensor w/NIST Certificate | FGD-0101-NIST | $117.00 |
| 2.8K Type Ultra Low -85C Temp Sensor w/Teflon Cable | FGD-0101-TEF | $45.00 |
| 2.8K Type Ultra Low -85C Temp w/Teflon Cable & NIST Certificate | FGD-0101TEFNIST | $135.00 |
| 10K Weatherproof Temperature Sensor | FGD-0102 | $27.00 |
| 10K Weatherproof Temperature Sensor - NIST | FGD-0102-NIST | $117.00 |
| 10 K Indoor Decorator Zone Temperature Sensor | FGD-0103 | $36.00 |
| 10K Outdoor Air Weatherproof Temperature Sensor | FGD-0104 | $63.00 |
| 10K Immersion Temperature Sensor | FGD-0105 | $65.00 |
| 2.8K Type Temperature Sensor in Glass Bead Vial | FGD-0107 | $49.50 |
| 2.8K Type Temperature Sensor in Glass Bead Vial & NIST Certificate | FGD-0107-NIST | $139.50 |
| 2.8K Type Ultra Low Temperature Sensor w/Teflon Cable | FGD-0107-TEF | $67.50 |
| 2.8K Type Ultra Low Temperature Sensor w/Teflon Cable & NIST Certificate | FGD-0107TEFNiST | $157.50 |
| LCD Readout for 2.8K Type Temperature Sensor | FGD-0120 | $116.99 |
| 2.8K Type Temperature Sensor in Glycol Vial | FGD-0127 | $49.50 |
| 2.8K Type Temperature Sensor in Glycol Vial & NIST | FGD-0127-NIST | $139.50 |
| 2.8K Type Ultra Low Temperature Sensor in Glycol Vial w/Teflon Cable | FGD-0127-TEF | $67.50 |
| 2.8K Type Ultra Low Temperature Sensor in Glycol Vial w/Teflon Cable & NIST Certificate | FGD-0127TEFNIST | $157.50 |
| J Type Thermocouple/4-20mA Converter | FGD-0220 | $399.00 |
| Float Switch | FGD-0222 | $35.10 |
| 4-20mA Type Dual Flow & Temperature Sensor - 1" Probe | FGD-0223-1 | $445.00 |
| 4-20mA Type Dual Flow & Temperature Sensor - 4" Probe | FGD-0223-4 | $449.00 |
| RTD probe w/4-20mA Transmitter (-200 to 35 C) | FGD-0240 | $285.00 |
| RTD probe w/4-20mA Transmitter (-200 to 204 C) | FGD-0240-SPEC | $310.00 |
| 14" RTD Probe with 4-20mA | FGD-0240-14 | $285.00 |
| RTD probe w/4-20mA Transmitter (User Specified Range) | FGD-0240-14SPEC | $310.00 |
| Ethernet to WiFi Adapter | FGD-0250 | $119.00 |
| Ethernet to WiFi Adapter Accessory | FGD-0250-U | $119.00 |
| 4-20mA Type Pressure Sensor | FGD-0301 | $149.00 |
| Differential Pressure Duct Sensor | FGD-0302-DUCT | $314.10 |
| 4-20mA Type Differential Pressure Sensor with Wall Mount Kit | FGD-0302-ROOM | $314.10 |
| 4-20mA Type Vibration Sensor | FGD-0303 | $349.00 |
| 4-20mA Type Vibration Sensor Mount | FGD-0303-MOUNT | $63.00 |
| PH Sensor 4-20mA Fixed | FGD-0305 | Call for Pricing |
| ORP Sensor 4-20mA Fixed | FGD-0315 | Call for Pricing |
| 4-20 Type Toroidal Conductivity Sensor, 0-10mS | FGD-0320 | Call for Pricing |
| 4-20 Type Toroidal Conductivity Sensor, 0-100mS | FGD-0321 | Call for Pricing |
| 4-20 Type Toroidal Conductivity Sensor, 0-1000mS | FGD-0322 | Call for Pricing |
| Dissolved Oxygen Transducer | FGD-0325 | Call for Pricing |
| Temp probe w/Glass Bead Vial, NIST and LCD Readout | FGD-VFC-GBV | $224.99 |
| Temp probe w/Glycol Vial, NIST and LCD Readout | FGD-VFC-GLY | $224.99 |
| AT&T Cell Modem for Cloud | FGD-4GLTE-AT | $1,075.50 |
| Rogers Cell Modem for Cloud | FGD-4GLTE-RW | $1,075.50 |
| Verizon Cell Modem for Cloud | FGD-4GLTE-VZ | $1,075.50 |
Sensaphone WSG30 and Accessories |
||
Sensaphone Model WSG30 |
Part # |
Price |
| Sensaphone WSG30 Wireless Sensor Gateway | FGD-WSG30 | $751.50 |
| Sensaphone WSG30 Wireless Sensor Gateway For 220VAC | FGD-WSG30-INT | $769.50 |
| Sensaphone WSG30 Wireless Sensor Gateway w/NEMA-4 Enclosure Clear Door | FGD-WSG30-CD | $895.50 |
| WSG Wireless Sensor Enclosure Kit | FGD-WSG30-SENCD | $50.00 |
Sensaphone Model WSG30 Accessories |
Part # |
Price |
| Mini Surge Protector - Power and Phone | FGD-0067 | $24.99 |
| Ethernet to WiFi Adapter | FGD-0250 | $119.00 |
| Ethernet to WiFi Adapter Accessory | FGD-0250-U | $119.00 |
| WSG Wireless Temperture Sensor | FGD-WSG30-TMP | $170.10 |
| WSG Wireless Temp w/ External Probe | FGD-WSG30-TEX | $179.10 |
| WSG Wireless Temperature Sensor w/External Probe & NIST Certificate | FGDWSG30TEXNIST | $269.10 |
| WSG Wireless Ultra Low Temperature Sensor w/External Probe & Teflon Cable | FGD-WSG30-TEX85 | $197.10 |
| WSG Wireless Ultra Low Temperature Sensor w/External Probe & Teflon Cable & NIST Certificate | FGDWSG30TX85NST | $287.10 |
| WSG Wireless Temperature Sensor w/Glass Bead Vial | FGD-WSG30-GBV | $211.50 |
| WSG Wireless Temp w/Glass Bead & NIST | FGDWSG30GBVNIST | $301.50 |
| WSG Wireless Temp Sensor in Glycol Vial | FGD-WSG30-GLY | $211.50 |
| WSG Wireless Temp Sensor in Glycol Vial with NIST Certificate | FGDWSG30GLYNIST | $301.50 |
| WSG Wireless Humidity Sensor | FGD-WSG30-HUM | $215.10 |
| WSG Wireless Dry Contact Sensor | FGD-WSG30-DRY | $170.10 |
| WSG Wireless Power Failure Sensor | FGD-WSG30-PWR | $179.10 |
| WSG Wireless Temperature Sensor w/ 1" RTD Probe | FGD-WSG30-RTD1 | $296.10 |
| WSG Wireless Temperature Sensor w/ 14" RTD Probe | FGD-WSG30-RTD14 | $314.10 |
| WSG Wireless Power Failure SensorWSG Wireless Temperature Sensor w/ 1" RTD Probe with NIST certificate | FGD-WSG30RTDNIST | $296.10 |
| WSG Wireless Temperature Sensor w/ 1" RTD Probe | FGD-WSG30-RTD1 | $296.10 |
| WSG Wireless Temperature Sensor w/ 14" RTD Probe | FGD-WSG30-RTD14 | $314.10 |
| WSG Wireless Power Failure SensorWSG Wireless Temperature Sensor w/ 1" RTD Probe with NIST certificate | FGD-WSG30RTDNIST | $296.10 |
| WSG 4-20mA Wireless Interface | FGD-WSG30-4-20 | $233.10 |
| WSG Wireless Spot Water Detection Sensor | FGD-WSG30-SPOT | $224.10 |
| WSG Wireless Zone Water Detection Sensor | FGD-WSG30-ZONE | $237.60 |
| Power Supply for WSG30 Wireless Sensors | XFR-0041 | $15.00 |
| Power Supply for WSG30 Wireless Zone Water Sensor Only | XFR-0046 | $15.00 |
| Power Supply for WSG30 Wireless Sensor Gateway | XFR-0047 | $15.00 |
| Power Supply for WSG30 Wireless Sensors for 220VAC | XFR-0048 | $15.00 |